Results 151 to 160 of about 115,907 (299)
Creep‐Induced Microstructural Evolution in an A2‐B2 Superalloy
Advanced Engineering Materials, EarlyView.A 27.3Ta‐27.3Mo‐27.3Ti‐8Cr‐10Al (at.%) refractory high‐entropy alloy with precipitation‐strengthened A2‐B2 microstructure was studied by creep tests at 1030°C, which demonstrate a transition in deformation mechanisms in the range of 100–150 MPa applied stress. This is associated with changes in dislocation–precipitate interactions. Relevant deformation
Liu Yang +10 more
wiley +1 more source
Influence of Test Temperature and Test Frequency on Fatigue Life of Aluminum Alloy EN AW‐2618A
Advanced Engineering Materials, EarlyView.The influence of test temperature and test frequency on the fatigue life of EN AW‐2618A is investigated. High‐cycle fatigue tests are performed at different test temperatures and frequencies on the 1000 h/230°C overaged state. Both test parameters reduce fatigue life due to time‐dependent damage mechanisms.
Ying Han +5 more
wiley +1 more source
Current Status and Challenges in Data Collection for Aerospace Coatings Deposited by Plasma Spraying
Advanced Engineering Materials, EarlyView.An innovative approach has been integrated into the GRENAT project to optimize plasma spraying and coating performance. Raw materials are accelerated and melted in the plasma generated by torches, creating coatings. Monitoring sensors collect process data which are combined with ex situ characterization data.
Lila Randriamananjara +8 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Reproduction of stacking fault energy calculations from literature with a semi‐automated large language model‐assisted extraction procedure: extraction of simulation protocol, atomistic structures, computational parameters, and reported results, ontology alignment, knowledge graph construction and, finally, recomputation forvalidation.
Sepideh Baghaee Ravari +5 more
wiley +1 more source
In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy
Advanced Engineering Materials, EarlyView.A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal +4 more
wiley +1 more source
A Uniform Temperature Bathtub Model [PDF]
Proceedings of the 2016 6th International Conference on Machinery, Materials, Environment, Biotechnology and Computer, 2016 openaire +1 more source
Advanced Engineering Materials, EarlyView.Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar +7 more
wiley +1 more source
Cathodic Cage Plasma Deposition of Nanostructured Cu–Fe–Se Coatings on Poly(methyl Methacrylate)
Advanced Engineering Materials, EarlyView.Nanostructured Cu–Fe–Se coatings are deposited on PMMA by a modified cathodic cage plasma process, enabling low‐temperature deposition on polymer substrates. A transition from discontinuous to compact morphology is observed with temperature, with optimal properties at 200°C, where improved CuFeSe2‐type bonding, lowest sheet resistance, and favorable ...
V. S. S. Sobrinho +8 more
wiley +1 more source
An Experimental High‐Throughput Approach for the Screening of Hard Magnet Materials
Advanced Engineering Materials, EarlyView.An entire workflow for the high‐throughput characterization and analysis of compositionally graded magnetic films is presented. Characterization protocols, data management tools and data analysis approaches are illustrated with test case Sm(Fe, V)12 based films.
William Rigaut +16 more
wiley +1 more source