Results 91 to 100 of about 134,530 (267)
Influencia de un recubrimiento de vinilo en la tensión de fractura del vidrio en ensayos de anillos concéntricos con gran superficie [PDF]
, 2014 El comportamiento post-rotura de los vidrios laminados es uno de los temas que están siendo investigados para explicar la capacidad de carga remanente tras la rotura de la primera lámina.
Alonso, Jesús +4 more
core +1 more source
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Modelos esfuerzo-deformación para mampostería fabricada en México D.F. [PDF]
, 2010 102 páginas. Maestría en Ingeniería Estructural.Si se desea estudiar el comportamiento de estructuras altas de mampostería se debe recurrir a modelos de análisis no lineal.
FLORES CANO, ADAN
core
Advanced Engineering Materials, EarlyView.Carbon nanomaterial‐reinforced epoxy composites exhibit pronounced piezoresistive behavior, enabling intrinsic damage sensing under cyclic and fatigue loading. This review critically compares carbon nanotube and graphene systems, correlating filler content, percolation threshold, and gauge factor with sensing stability and damage evolution.
J. M. Parente +3 more
wiley +1 more source
Propiedades de los hilados por zunchado neumático comparados con las de los hilados. [PDF]
, 1992 El presente trabajo trata la problemática de la hilatura de la fibra celulósica de alto módulo MODAL según la técnica de hilatura de zunchado neumático por doble tobera de torsión fugaz.
Coll Tortosa, Liberto +2 more
core
Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere
Advanced Engineering Materials, EarlyView.A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert +6 more
wiley +1 more source
How does the ultrasonic assist CO2 immiscible flooding?
Ultrasonics SonochemistryCO2 flooding is considered one of the most important methods for reducing CO2 emissions and increasing oil production from reservoirs. However, the challenges of low recovery rates and poor economic benefits in CO2 immiscible flooding significantly ...
Hengli Wang +6 more
doaj +1 more source
工程科学学报, 2015 A mathematical model to describe the wave-shaped defect generation and stretching process of thin strips is established by using ABAQUS to study the stress characteristics and deformation behavior of strips under initial strain.
ZHANG Qing-dong, ZHOU Sui, YIN Jia-chen
doaj +1 more source
Advanced Engineering Materials, EarlyView.The wettability of aluminum droplets (Al) on different copper substrates (Cu), where liquid Al spreads on solid Cu surfaces to form a liquid–solid interface, is studied numerically and experimentally. The experimental and numerical results show good agreement in the fast‐spreading regime.
Shan Lyu +8 more
wiley +1 more source