Results 71 to 80 of about 558,784 (301)

Fabrication Routes for Ionic Conducting Fiber Strain Sensors

Advanced Engineering Materials, EarlyView.
Ionic conducting fiber strain sensors (ICFSs) offer compliant, textile‐integrable sensing. Thus far, the commercialization of ICFSs has been constrained by fiber fabrication routes. This review provides a fabrication‐centric analysis of ICFSs correlating processing strategies with material properties and scalability.
Leo John Kershaw, Zhanhong Yang, Anne Ladegaard Skov, Magdalena Skowyra   +3 more
wiley   +1 more source

Tensile properties of nanoclay reinforced epoxy composites

, 2013
Kinetic epoxy resin was filled with nanoclay to increase tensile properties of the composite for civil and structural. This project manufactured samples with different percentages by weight of nanoclay in the composites in steps of 1 wt%, which were then
Ku, H., H. Ku, Mohan Trada, Trada, Mohan
core   +1 more source

On the static and dynamic properties of flax and Cordenka epoxy composites [PDF]

, 2013
Fibre reinforced composites have excellent specific properties and are widely sought after by engineers seeking to reduce mass. However, end of life disposal is a significant problem and so research into more sustainable natural fibre composites is ...
Kirwan, Kerry, Collings, Ed, Müssig, Jorg, Meredith, James O., Coles, Stuart R., Weager, Brendon, Cozien-Cazuc, Sophie, Powe, Richard   +7 more
core   +1 more source

Redesigned crinkle washer for piezoelectric energy generation

Frontiers in Mechanical Engineering
Structures are used for piezoelectric energy harvesters as a way of redirecting the path of an inputted force so that the piezoelectric element can better convert the mechanical energy to electrical energy.
Fergus Crawley, Khalifa Ibrahim, Qing Qin, Zhenhua Luo   +3 more
doaj   +1 more source

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

Dynamic Tensile Test of Granite and Its Tensile Sensitivity

Advances in Civil Engineering, 2020
Through the dynamic splitting tensile test under various loading rates, different mechanical parameters have been analyzed; not only the dynamic peak stress but also the dynamic peak strain has a good linear relationship with the strain rate. The tensile sensitivity obtained from the dynamic tensile test increases with strain rate gradually, and it ...
Ke Man, Zhifei Song, Xiaoli Liu
openaire   +2 more sources

Weldability Characteristics of Sintered Hot-Forged AISI 4135 Steel Produced through P/M Route by Using Pulsed Current Gas Tungsten Arc Welding

High Temperature Materials and Processes, 2016
Present investigation is an attempt to study the weldability characteristics of sintered hot-forged plates of AISI 4135 steel produced through powder metallurgy (P/M) route using matching filler materials of ER80S B2.
Joseph Joby, Muthukumaran S., Pandey K.S.   +2 more
doaj   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Improvement in plasticity of Al-Cu-Mg alloy by electromagnetic coupling treatment [PDF]

MATEC Web of Conferences
Electromagnetic coupling treatment (EMCT) is a new method to regulate material properties. To investigate the effect of EMCT on the plasticity of the Al-Cu-Mg alloy, a software simulation calculation was carried out, and then the alloy was treated with ...
Zeng Bo, Chen Dongyan, Sun Hongfei, Deng Juan, Wang Jie, Huang Kunlan   +5 more
doaj   +1 more source

Gallium Microalloying in Bi–Sn Solders: Interfacial Phase Formation, Wettability, and Long‐Term Shear Reliability Under Isothermal Aging

Advanced Engineering Materials, EarlyView.
Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová, Markéta Klimtová, Mohd Faizul Mohd Sabri, Yew Hoong Wong, Petr Veselý, Martin Plaček, Karel Dušek   +6 more
wiley   +1 more source