Results 141 to 150 of about 2,434,979 (181)

Conjugated Polymers Engineered for Flexible/Stretchable Electronics

open access: yesJournal of Polymer Science, EarlyView.
This review highlights glass transition temperature (Tg) as the central parameter linking molecular structure to device performance in conjugated polymers. By tuning backbone rigidity, side‐chain architecture, and dynamic bonding, Tg governs the balance between π–π stacking–enabled charge transport and mechanical compliance.
Yunchong Yang   +5 more
wiley   +1 more source

In Situ Curing‐Enabled 3D Printing of Continuous Fiber‐Reinforced Thermosetting Composites

open access: yesJournal of Polymer Science, EarlyView.
In situ curing‐enabled the 3D printing of continuous fiber/thermoset composites, which were reviewed. Particularly, four types of in situ curing, were discussed, including Radiation‐induced curing, photothermal curing, electrothermal curing, and frontal polymerization. AI‐integrated printing was also analyzed.
Xiaofei Wu   +2 more
wiley   +1 more source

Intelligent Continuum Micromachines in Complex Confined Spaces

open access: yesSmartBot, EarlyView.
The cover depicts a conceptual design for an intelligent continuum micromachine entering a target capsule used in fusion‐energy research through its slender gas‐fill tube. By combining route‐adaptive deformation, embedded sensing, and a functional end effector, the robot could inspect hidden defects, assess local conditions, and support localized ...
Huayang Sai   +7 more
wiley   +1 more source

An Ergonomic Customizable Soft Robotic Glove Toward Personalized Hand Rehabilitation

open access: yesSmartBot, EarlyView.
Soft robotic gloves for hand rehabilitation are often limited by poor fit and uneven pressure on the fingers. Here, the authors report an ergonomic all‐fabric glove whose dual‐action actuators are tailored to individual finger geometry by CNC heat sealing, with symmetrical chambers that distribute interface pressure more evenly. Weighing only 90 g, the
Rui Chen   +13 more
wiley   +1 more source

Three‐Dimensional Piezoelectric Fibrous Constructs for Muscle Regeneration

open access: yesSmall, EarlyView.
This study fabricates 3D piezoelectric PHBV scaffolds to enhance muscle regeneration by systematically tuning electrospinning parameters. Introducing porosity yields a 25‐fold enhancement in the effective piezoelectric coefficient (d33). A highly effective d33 signal, activated by cellular tension and fiber deformation, significantly improves myogenic ...
Xenofon Karagiorgis   +14 more
wiley   +1 more source

Progress in Explosion Mechanisms and Prevention Technologies for Direct Chill Casting Aluminum Melt Upon Water Contact: A Review

open access: yesSafety Science and Technology, EarlyView.
Molten aluminum–water explosion triggered by leakage remains the core unresolved safety hazard hindering safe production in aluminum direct chill casting. This review summarizes its explosion mechanism, key influencing factors, prevention technologies, existing gaps, and prospects of intelligent multi‐technology integrated explosion‐proof systems ...
Min Wang   +5 more
wiley   +1 more source

Structural capacity of precast concrete walls with openings: A parametric study on connection types and reinforcement ratios

open access: yesStructural Concrete, EarlyView.
Abstract The structural role of precast concrete walls with openings is often overlooked in design practice due to concerns about reduced stiffness, stress concentration, cracking around openings, and potential unexpected failure modes under seismic loading.
Gonçalo Marreneca   +2 more
wiley   +1 more source

The influence of secondary reinforcement on a strut‐and‐tie model for the design of reinforced concrete corbels

open access: yesStructural Concrete, EarlyView.
Abstract In precast concrete structures, optimizing the design of corbels by considering the contributions of secondary reinforcement elements can significantly improve construction economy, especially when corbels are repeated multiple times. This paper proposes a strut‐and‐tie model for reinforced concrete corbels subjected to vertical and/or ...
Rejane Martins Fernandes Canha   +3 more
wiley   +1 more source

Structural behavior of small square steel tubes reinforced self‐compacting concrete columns under biaxial eccentric loads

open access: yesStructural Concrete, EarlyView.
Abstract In this study, the structural behavior of small square steel tube‐reinforced self‐compacting concrete (SSTR‐SCC) columns is investigated under symmetric and asymmetric biaxial eccentric loads. Twelve specimens were cast and tested under biaxial eccentric loads.
Muhammad Naveed   +2 more
wiley   +1 more source

Evaluation of cold joint effects on the microstructure and mechanical behavior of three‐dimensional printed concrete specimen

open access: yesStructural Concrete, EarlyView.
Abstract 3D concrete printing (3DCP) is an automated construction technique that uses an extrusion process to fabricate structures efficiently. However, the layer‐by‐layer process can create interlayer weaknesses, and interruptions during printing can result in cold joints, which can negatively affect the structural behavior.
Sung‐Jo Kim   +3 more
wiley   +1 more source

Home - About - Disclaimer - Privacy