Results 61 to 70 of about 600,107 (298)

Mechanical tensile properties of the anterolateral ligament

Journal of Experimental Orthopaedics, 2015
Background In a noticeable percentage of patients anterolateral rotational instabilities (ALRI) remain after an isolated ACL reconstruction. Those instabilities may occur due to an insufficiently directed damage of anterolateral structures that is often ...
Martin Zens, Matthias J Feucht, Johannes Ruhhammer, Anke Bernstein, Hermann O Mayr, Norbert P Südkamp, Peter Woias, Philipp Niemeyer   +7 more
doaj   +1 more source

Mechanical properties of crepe paper and chickpaper [PDF]

Journal of Central European Agriculture, 2016
The paper deals with the evaluation of the mechanical properties of the crepe paper and chickpaper. The thickness of crepe paper was 300 m with the surface mass 150 g*m-2 and chickpaper paper thickness was 100 m with the surface mass 40 g*m-2.
Ľubomír KUBÍK, Iveta BOĎOVÁ
doaj   +1 more source

Modeling the correlation between texture characteristics and tensile properties of AZ31 magnesium alloy based on the artificial neural networks

Journal of Materials Research and Technology, 2023
This work is aimed to investigate the relationship between the texture and tensile properties of the AZ31 Mg alloy by the machine learning method. The texture characteristics parameters, namely the maximum pole intensity (Imax), texture dispersion (D ...
Yibing Zhang, Shengwen Bai, Bin Jiang, Kun Li, Zhihua Dong, Fusheng Pan   +5 more
doaj   +1 more source

Pre-fatigue influence on quasi-static tensile properties of Ti-6Al-4V in thin-sheet form [PDF]

, 2010
The response of engineering structures to loads is most often assessed without taking possible damage of the used material(s) into account. However, it has already been proved that a preceding cyclic loading and the alteration of the microstructure it ...
De Baere, Ives, Degrieck, Joris, Galan Lopez, Jesus, Verleysen, Patricia   +3 more
core   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Experimental-based statistical models for the tensile characterization of synthetic fiber ropes: a machine learning approach

Scientific Reports, 2023
This study investigated the tensile behavior of some prevalent synthetic fiber ropes made of polyester, polypropylene, and nylon polymeric fibers. The aim was to generate well-documented experimental statistics and develop simplified stress–strain ...
Yahia Halabi, Hu Xu, Zhixiang Yu, Wael Alhaddad, Isabelle Dreier   +4 more
doaj   +1 more source

EBSD Study of Creep‐Induced Lattice Misorientation in MgO‐Particle‐Reinforced Austenitic Steel Composites

Advanced Engineering Materials, EarlyView.
Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller, Amaya Compart, Mahnaz Mehdizadehlima, Serhii Yaroshevskyi, Christos G. Aneziris, Horst Biermann, Anja Weidner   +6 more
wiley   +1 more source

Measurement of tensile properties of selected rovings

Acta Polytechnica CTU Proceedings
This article is focused on measuring the tensile properties of chosen fibre materials, such as flax, alkali resistant glass or viscose. All selected materials were tested both pure and impregnated using epoxy resin. In this article, the tensile strength
Věra Kabíčková, Jakub Hájek, Jan Macháček, Eliška Kafková, Tomáš Vlach   +4 more
doaj   +1 more source

Tensile properties of in-situ precipitated polydimethylsiloxane networks

eXPRESS Polymer Letters, 2013
Tensile propertiesof polydimethylsiloxane (PDMS) networks filled with in-situ precipitated silica were investigated. Experimental results showed that increasing the swelling time of cured rubber sheets in tetraethoxysilane (TEOS) solution or elevating ...
Z. Zhang, Y-L. Yue, C. Zhang, H. Zhang, D-H. Zhang, X. Chen, Y-F. Chen   +6 more
doaj   +1 more source

Lightweight aluminum casting alloy is useful at cryogenic temperatures [PDF]

, 1965
M-45, a lightweight, high purity aluminum casting alloy has superior tensile properties for use at cryogenic ...

core   +1 more source