Results 161 to 170 of about 8,559,227 (400)

Enhanced Morphology-Dependent Tensile Property and Breakdown Strength of Impact Polypropylene Copolymer for Cable Insulation. [PDF]

Materials (Basel), 2020
Yang K, Liu Y, Yan Z, Tian Y, Liu Y, Jing Z, Li J, Li S.   +7 more
europepmc   +1 more source

Tensile properties of copper, nickel, and 70-percent-copper-30-percent-nickel and 30-percent-copper-70-percent-nickel alloys at high temperatures

, 1957
William D. Jenkins, T.G. Digges, Carl R. Johnson   +2 more
openalex   +1 more source

Tensile Properties of Human Lumbar Longitudinal Ligaments [PDF]

, 1968
H Tkaczuk
openalex   +1 more source

Microstructural Evolution and Mechanical Properties of a Medium‐Manganese Steel Manufactured by Laser‐Based Powder Bed Fusion of Metals

Advanced Engineering Materials, EarlyView.
Fe–12Mn–0.2C medium‐manganese steel is processed by laser‐based powder bed fusion of metals using blended as well as pre‐alloyed powder. Various scanning speeds are used to determine the influence of energy deposition rate on microstructure and mechanical properties.
Leoni Hübner, Bugra Köksal, Thomas Wegener, Christian Haase, Thomas Niendorf   +4 more
wiley   +1 more source

The penetration of hydrogen into metal cathodes and its effect upon the tensile properties of metals and their resistance to repeated stresses; with a note on the effect of non electrolytic baths and nickel plating on these properties

, 1929
F. C. Lea
openalex   +1 more source

Tensile Properties of NaCl‐BaNr Solid Solution Single Crystals [PDF]

, 1963
F. T. Wimmer, W. Kobes, M. E. Fine
openalex   +1 more source

The Structural Refinement of Commercial‐Purity Copper Processed by Equal Channel Angular Pressing with Low Strain Amplitude

Advanced Engineering Materials, EarlyView.
Equal channel angular pressing of commercial pure copper under low strain amplitude (≈0.48) induces concurrent continuous and localized discontinuous dynamic recrystallization, forming a duplex structure influenced by strain heterogeneity and recovery. Moderate hardening after 4–12 passes results from progressive high‐angle grain boundary formation via
Paula Cibely Alves Flausino, Nayara A. N. da Silva, Bárbara C. de Almeida, Taise M. Manhabosco, Elaine C. S. Corrêa, Maria T. P. Aguilar, Paulo R. Cetlin   +6 more
wiley   +1 more source

Impact Resistance and Tensile Properties of Metals at Subatmospheric Temperatures

, 1941
H. W. Gillett
openalex   +2 more sources

Influence of 3D Printing FDM Process Parameters on Tensile Property of ULTEM 9085

Procedia Manufacturing, 2019
Aboma Wagari Gebisa, H. Lemu
semanticscholar   +1 more source

Design of Multiphase Compositionally Complex Alloys for Enhanced Hardness at Elevated Temperatures and Machinability: Comparative Study with Inconel 718

Advanced Engineering Materials, EarlyView.
This study compares the mechanical properties of Inconel 718 with two newly developed compositionally complex alloys (CCAs). Inco‐like‐H alloy demonstrates significantly improved wear resistance, surface finish, and hardness, notably at high temperatures. This CCA requires no heat treatment and is well suited for additive manufacturing. Its performance
Laurent Peltier, Gaël Le Coz, Fodil Meraghni, Jérome Slowensky   +3 more
wiley   +1 more source