Results 31 to 40 of about 221,965 (306)
Effects of Bi on the microstructure and mechanical property of ZK60 alloy
Journal of Magnesium and Alloys, 2015 Microstructures and phase compositions of as-cast and extruded ZK60-xBi (x = 0–1.64) alloys were investigated. Meanwhile, the tensile mechanical property and hardness were tested.
Zhenghua Huang +4 more
doaj +1 more source
Tensile Fracture Property of Concrete Affected by Interfacial Transition Zone
International Journal of Concrete Structures and Materials, 2023 As a weak link between aggregate and mortar in concrete, interfacial transition zone (ITZ) usually plays a key role in concrete fracture. To investigate the tensile fracture property of concrete affected by the mechanical properties of ITZ numerically ...
Heli Ji, Xinhua Yang, Zuyun Luo, Fan Bai
doaj +1 more source
Preparation and Properties of Opaque Polyethylene Terephthalate/TiO2 Filaments
Medžiagotyra, 2021 The opaque polyethylene terephthalate (PET) filaments with different mass fractions of TiO2 particles were prepared by low-speed melt spinning and drafting.
Zhaolin LIU +4 more
doaj +1 more source
Experimental Analysis of Tensile Mechanical Properties of Sprayed FRP
Advances in Materials Science and Engineering, 2016 To study the tensile mechanical properties of sprayed FRP, 13 groups of specimens were tested through uniaxial tensile experiments, being analyzed about stress-strain curve, tensile strength, elastic modulus, breaking elongation, and other mechanical ...
Zhao Yang, Kun Wu
doaj +1 more source
Metals, 2022 Partial replacement of Si by Al improves the coatability (or galvanizing property) of Si-Mn advanced high-strength steel (AHSS) sheets. In this paper, the effects of the partial replacement on the microstructure, tensile property, and cold formability ...
Koh-ichi Sugimoto
doaj +1 more source
The influence of fibre length, diameter and concentration on the strength and strain to failure of glass fibre-reinforced polyamide 6,6 [PDF]
, 2008 Results of an investigation of the mechanical performance of injection moulded long glass fibre-reinforced polyamide 6,6 composites are presented. The glass fibre content in these composites was varied over the range 10-50% by weight using fibres with ...
Akay +26 more
core +1 more source
High Temperature Materials and Processes, 2017 Defect-free joint of Ti–6Al–4V alloy was successfully friction stir welded below β-transus temperature and then tensile tests were performed. Microstructure, macrostructure, tensile properties and fracture position are mainly discussed in order to ...
Ji Shude +5 more
doaj +1 more source
Journal of Materials Research and Technology, 2020 The microstructure and tensile property of the hypoeutectic Al-Si alloy with and without microalloying of Sc and Zr were studied by means of the optical microscope (OM), Transmission electron microscopy (TEM) and the tensile test.
Jiqiang Chen +5 more
doaj +1 more source
Engineering characteristics of Egyptian limestone [PDF]
, 2019 Purpose. Study of physical properties such as porosity, density and mechanical properties such as compressive strength and tensile strength of Egyptian limestone based on experimental investigations. Methods.
Haitham, M. Ahmed, Mahrous, A.M. Ali
core +1 more source
Effect of Pre-sretching Processing on Microstructures and Properties of 2A97 Al-Li Alloy
Journal of Aeronautical Materials, 2016 The effect of pre-sretching processing before artificial aging on the microstructures and properties of 2A97 Al-Li alloy was investigated by using tensile test,corrosion test and transmission electron microscope(TEM) observations.
YU Juan +3 more
doaj +1 more source