Results 71 to 80 of about 221,965 (306)
Advanced Engineering Materials, EarlyView.This article presents the NFDI‐MatWerk Ontology (MWO), a Basic Formal Ontology‐based framework for interoperable research data management in materials science and engineering (MSE). Covering consortium structures, research data management resources, services, and instruments, MWO enables semantic integration, Findable, Accessible, Interoperable, and ...
Hossein Beygi Nasrabadi +4 more
wiley +1 more source
Nanofiller Fibre-Reinforced Polymer Nanocomposites [PDF]
, 2008 In this work, the technology of nano and micro-scale particle reinforcement concerning various polymeric fibre-reinforced systems including polyamides (PA), polyesters, polyurethanes, polypropylenes and high performance/temperature engineering ...
Desai, S. +2 more
core +1 more source
Tensile Properties of Jute-Polypropylene Composites
Chemical Engineering Transactions, 2018 This paper describes the tensile behaviour of jute-polypropylene fibre composites with different fibre volume fractions. Here, the composite laminates consisting of weaving jute fibres, with the fibre volume percent in the range of 20 to 80 % and polypropylene plies were prepared using hand lamination.
Mohd. Bakhori, Siti Nadia +4 more
openaire +3 more sources
Tensile properties of orthodontic elastomeric chains [PDF]
The European Journal of Orthodontics, 2004 The purpose of this investigation was to assess the permanent elongation, tensile strength and toughness of elastomeric chains. Two types (open and closed chains, i.e. with and without an intermodular link) of three brands of elastomeric module yielding six groups were included in the study.
Eliades, T. +3 more
openaire +3 more sources
Advanced Engineering Materials, EarlyView.High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé +5 more
wiley +1 more source
Strength Properties of Preceramic Brazed Joints of a Gold-Palladium Alloy with a Microwave-assisted Oven and Gas/Oxygen Torch Technique [PDF]
, 2014 Statement of problem The effect of microwave brazing on the strength properties of dental casting alloys is not yet known. Purpose The purpose of this study was to compare the strength properties of preceramic brazed joints obtained by using a microwave
Dunford, Robert +3 more
core +1 more source
Influence of matrix toughness and interfacial strength on the toughness of epoxy composites with ductile steel fabric reinforcement [PDF]
, 2015 In the last decades, several studies have been performed on polymers reinforced with steel cords or wires. However, the diameter of these steel reinforcements was still quite large (200 micron and more).
Degrieck, Joris +3 more
core +2 more sources
Advanced Engineering Materials, EarlyView.It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti +11 more
wiley +1 more source
Scientific ReportsIn this study, the structural optimization, the direct-reverse superplastic forming (SPF) process the thickness distribution and the tensile property of the industrial 5083 aluminum alloy pallet with multi-deep cavities were investigated.
Zhihao Du +6 more
doaj +1 more source
The Effect on Tensile Property of Surface Treatment of MWNTs on MWNTs/PI Films
Journal of Harbin University of Science and Technology, 2017 We discussed the effects of MWNTs surface treatments on MWNTs/PI hybrid films in tensile strength. Used by ultrasonic，mixed acid and Fenton three methods to treat MWNTs，then through in-situ polymerization and heat imidization to prepare MWNTs/PI hybrid ...
ZHANG Ming-yan +3 more
doaj +1 more source