Results 51 to 60 of about 588,415 (310)

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Experimental study and verification on tensile strength of remolded clay

Shuiwen dizhi gongcheng dizhi
The tensile strength of clay is an important factor in determining the stability of soil slope. Due to the fragmentation of soil, the understanding of the tensile strength of clay is not clear. In this study, the uniaxial tensile test of remolded clay is
Shuaixin BAI, Chao YIN, Weiqing MENG, Shuaiwei WANG, Yongxiang ZHENG, Wei WANG   +5 more
doaj   +1 more source

The Statistical Analysis of Relation between Compressive and Tensile/Flexural Strength of High Performance Concrete

Archives of Civil Engineering, 2016
This paper addresses the tensile and flexural strength of HPC (high performance concrete). The aim of the paper is to analyse the efficiency of models proposed in different codes.
Kępniak M., Woyciechowski P.
doaj   +1 more source

The Effect of Mg Adding in Recycled Aluminum Casting on Tensile Strength and Microstructure

Logic, 2020
The problems faced are aluminum (Al) waste from industries that damage the environment and scarcity of Al raw materials that need to be recycled from used Al.
Syamsul Hadi, Ahmad Hailala Nur Aziz, Pipit Wahyu Nugroho, Muhammad Akhlis Rizza, Hangga Wicaksono   +4 more
doaj   +1 more source

Microstructural Evolution and Vacancy Defect Formation in Mn–Mo–Ni RPV Steel Under Low Cycle Fatigue: Insights From EBSD and PALS

Advanced Engineering Materials, EarlyView.
Low‐cycle fatigue damage in Mn–Mo–Ni reactor pressure vessel steel is examined using a combined electron backscatter diffraction and positron annihilation lifetime spectroscopy approach. The study correlates texture evolution, dislocation substructure development, and vacancy‐type defect formation across uniform, necked, and fracture regions, providing
Apu Sarkar, Dhanadeep Dutta, G. Bharat Reddy   +2 more
wiley   +1 more source

Compressive and Tensile Strength of Expanded Polystyrene Beads Concrete [PDF]

, 2005
Penelitian ini betujuan untuk mempelajari property dari beton ringan yang mengandung expanded polystyrene beads, yaitu kuat tekan (compressive strength) dan kuat tarik (tensile strength). Property tersebut kemudian dibandingkan dengan beton normal (beton
Subhan, T. F. (Tengku)
core  

EBSD Study of Creep‐Induced Lattice Misorientation in MgO‐Particle‐Reinforced Austenitic Steel Composites

Advanced Engineering Materials, EarlyView.
Creep experiments at 900°C on coarse‐grained steel‐ceramic composites containing recycled magnesia reveal that higher ceramic volume fractions significantly enhance the creep resistance. Detailed EBSD investigations identify subgrain formation in the steel matrix as the dominant deformation mechanism.
Moritz Müller, Amaya Compart, Mahnaz Mehdizadehlima, Serhii Yaroshevskyi, Christos G. Aneziris, Horst Biermann, Anja Weidner   +6 more
wiley   +1 more source

The use of the Box–Behnken experimental design to model tensile strength of spunlaced fabrics and evaluating fabrics behaviour in acidic condition

Journal of Industrial Textiles, 2022
Determining the tensile strength of nonwoven fabrics is one of the important factors considered for operational performance of the fabrics, especially for fabrics that are exposed to acidic condition.
Lebo Maduna, Asis Patnaik, Rajkishore Nayak   +2 more
doaj   +1 more source

A Numerical–Experimental Approach for Multi‐Matrix Fiber‐Reinforced Plastics Characterization Using Finite Element Model Updating

Advanced Engineering Materials, EarlyView.
A numerical–experimental framework is developed for characterizing multi‐matrix fiber‐reinforced polymers (MM‐FRPs) combining epoxy and polyurethane matrices. Harmonic bending tests are integrated with finite element model updating (FEMU) to simultaneously identify elastic and viscoelastic material parameters.
Rodrigo M. Dartora, Tales V. Lisbôa, Axel Spickenheuer, Rogério J. Marczak, Jakson M. Vassoler   +4 more
wiley   +1 more source

Study on mechanical properties and strength relation between cube and cylinder specimens of steel fiber reinforced concrete

Advances in Mechanical Engineering, 2019
An experimental study was performed on the splitting tensile strength of steel fiber reinforced concrete using cube and cylinder specimens. Effects of volume fraction, aspect ratio, geometry, and tensile strength of steel fiber on the splitting tensile ...
Haitang Zhu, Chuanchuan Li, Danying Gao, Lin Yang, Shengzhao Cheng   +4 more
doaj   +1 more source