Results 111 to 120 of about 173,844 (313)

Unsupervised Deep Learning for Advanced Forming Limit Analysis in Sheet Metal: A Tensile Test-Based Approach. [PDF]

Materials (Basel), 2023
Thamm A, Thamm F, Sawodny A, Zeitler S, Merklein M, Maier A.   +5 more
europepmc   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

Determining the effect of strain rate on the fracture of sheet steel [PDF]

A key challenge for the automotive industry is to reduce vehicle mass without compromising on crash safety. To achieve this, it is necessary to model local failure in a material rather than design to the overly conservative criteria of total elongation
Beaumont, Richard Adrian
core  

Static tensile test of materials

, 2018
This Final Year Project (FYP) presents the project B207, Static Tensile Test of materials. In this project, the static tensile test will mainly focus on studying the properties of Aluminium 6061-T6.
Toh, Winston Xin Wei
core   +1 more source

Biaxial tensile test and meso damage numerical simulation of HTPB propellant. [PDF]

Sci Rep, 2022
Wang Q, Wang G, Wang Z, Qiang H, Wang X, Li S, Zhu Z.   +6 more
europepmc   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source

Application of a Tensile Test Method to Identify the Ductile-Brittle Transition of Caramel. [PDF]

Foods, 2022
Schab D, Tiedemann L, Rohm H, Zahn S.
europepmc   +1 more source

Toward Knowledge‐Based Workflows: A Semantic Approach to Atomistic Simulations for Mechanical and Thermodynamic Properties

Advanced Engineering Materials, EarlyView.
Knowledge‐based atomistic workflows are presented for mechanical and thermodynamic properties. By coupling modular simulations with ontology‐aligned metadata and provenance, Fe case studies on elastic behavior, defects, thermal properties, and Hall–Petch strengthening reveal how FAIR, queryable, and reusable simulation data can be generated. Mechanical
Abril Azócar Guzmán, Hoang‐Thien Luu, Sarath Menon, Tilmann Hickel, Nina Merkert, Stefan Sandfeld   +5 more
wiley   +1 more source

Tensile and Dynamic Toughness of Kenaf Fiber-Reinforced Epoxy Composites

Fibers
The environmental impact of petroleum-based materials in driving climate change has stimulated growing interest in natural lignocellulosic fibers (NLFs) as reinforcements for polymeric matrices.
Thuane Teixeira da Silva, Matheus Pereira Ribeiro, Lucas de Mendonça Neuba, Pedro Henrique Poubel Mendonça da Silveira, Noan Tonini Simonassi, Sergio Neves Monteiro, Lucio Fabio Cassiano Nascimento   +6 more
doaj   +1 more source

Categorize the existing clamps used for tensile test of human graft- a systematic review. [PDF]

BMC Musculoskelet Disord, 2022
Farago D, Kozma B, Kiss RM.
europepmc   +1 more source