Results 111 to 120 of about 16,160,711 (399)
Testing filamentary composites [PDF]
, 1970 NOL ring split-dee tensile test has the advantages that the specimen is readily fabricated by winding and the test is performed in a conventional testing machine without special fixtures.
Dow, N. F., Rosen, B. W.
core +1 more source
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source
Pre-fatigue influence on quasi-static tensile properties of Ti-6Al-4V in thin-sheet form [PDF]
, 2010 The response of engineering structures to loads is most often assessed without taking possible damage of the used material(s) into account. However, it has already been proved that a preceding cyclic loading and the alteration of the microstructure it ...
De Baere, Ives +3 more
core +1 more source
Effect of surface treatments on the cross-section area and on the tensile properties of sisal fibers
Journal of Natural Fibers, 2019 This work deals with the effect that surface treatments can cause on the cross-section and on the tensile properties of sisal fibers. The simplest treatment of washing in tap water, at room temperature and at 60°C, was compared with mercerization ...
D.C.P. Quinaya, J.R.M. d’Almeida
doaj +1 more source
Advanced Engineering Materials, EarlyView.Phase‐field simulations coupled with dislocation‐density‐based crystal plasticity modeling reproduce γ′ rafting behavior in single‐crystal Ni‐based superalloys under varied loading conditions. The model captures both macroscopic creep and microscopic morphology evolution, with results matching high‐temperature creep experiments.
Micheal Younan +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Additive manufacturing provides precise control over the placement of continuous fibres within polymer matrices, enabling customised mechanical performance in composite components. This article explores processing strategies, mechanical testing, and modelling approaches for additive manufactured continuous fibre‐reinforced composites.
Cherian Thomas, Amir Hosein Sakhaei
wiley +1 more source
Tensile mechanical properties tests of non-standard component in high temperature [PDF]
, 2017 Wei Su +3 more
openalex +1 more source
Successfully estimating tensile strength by small punch testing
Ubiquity Proceedings, 2018 The Small Punch (SP) test is a relatively simple test well suited for material ranking and material property estimation in situations where standard testing is not possible or considered too material consuming. The material tensile properties, e.g.
S. Holmström +5 more
doaj +1 more source
Phase Field Failure Modeling: Brittle‐Ductile Dual‐Phase Microstructures under Compressive Loading
Advanced Engineering Materials, EarlyView.The approach by Amor and the approach by Miehe and Zhang for asymmetric damage behavior in the phase field method for fracture are compared regarding their fitness for microcrack‐based failure modeling. The comparison is performed for the case of a dual‐phase microstructure with a brittle and a ductile constituent.
Jakob Huber, Jan Torgersen, Ewald Werner
wiley +1 more source
Static tensile and tensile creep testing of five ceramic fibers at elevated temperatures [PDF]
Static tensile and tensile creep testing of five ceramic fibers at elevated temperature was performed. J.P. Stevens, Co., Astroquartz 9288 glass fiber, Nippon Carbon, Ltd., (Dow Corning) Nicalon NLM-102 silicon carbide fiber, and 3M Company Nextel 312 ...
Adams, Donald F., Zimmerman, Richard S.
core +1 more source