Results 141 to 150 of about 16,160,711 (399)

Pemodelan Pengujian Tarik Untuk Menganalisis Sifat Mekanik Material [PDF]

, 2013
One of the tests used to determine the mechanical properties of the metal are tensile test. The results obtained from tensile testing is the yield strength of the material.
Poeng, R. (Rudy), Salindeho, R. D. (Robert), Soukotta, J. (Jan)   +2 more
core  

Comparative Study of The Asphalt Mix Stiffness Modulus Using Selected Test Methods – 2-Point Bending Test, 4-Point Bending Test and Indirect Tensile Test

, 2023
Majda Belhaj, Jan Valentin
openalex   +1 more source

Enhanced Strength and Corrosion Resistance of Ti‐13Nb‐12Ta‐10Zr‐4Sn Alloy by Aging Treatment

Advanced Engineering Materials, EarlyView.
This work systematically investigates the effect of aging treatment on mechanical properties and corrosion behavior of vacuum arc‐melted Ti‐13Nb‐12Ta‐10Zr‐4Sn alloy. Owing to the increased α″ martensite, strength and corrosion resistance were significantly enhanced by aging treatment.
Yuhua Li, Rong Zhao, Qian Zhang, Haojie Wang, Yujing Liu, Lai‐Chang Zhang   +5 more
wiley   +1 more source

Bioinspired Shape‐Memory Hook Fasteners With Programmable Interlocking and Silent Release

Advanced Engineering Materials, EarlyView.
Bioinspired hook fasteners made from epoxy shape‐memory polymers are shown to switch between strong, secure attachment and gentle, silent release when heated. By combining programmable geometry and material response, these adaptive fasteners outperform commercial systems in strength and noise control, enabling new solutions for robotics, medical ...
Maria I. Vallejo Ciro, Manuel J. Carvajal Loaiza, Rahaf Homssi, Vanessa Restrepo   +3 more
wiley   +1 more source

Small punch tensile/fracture test data for Zircaloy 4 material at 300 °C and a displacement rate of .005 mm/s

, 2016
Frits De Haan, Stefan Holmström, Burkhard Fischer   +2 more
openalex   +2 more sources

Artificial Neural Network-Based Structural Analysis of 3D-Printed Polyethylene Terephthalate Glycol Tensile Specimens

Machines
Materials are a mainstay of both industry and everyday life. The manufacturing and processing of materials is a very important sector as it affects both the mechanical properties and the usage of the final products.
Athanasios Manavis, Anastasios Tzotzis, Lazaros Firtikiadis, Panagiotis Kyratsis   +3 more
doaj   +1 more source

Evaluation of Plasticity and Creep Parameters From Tensile Stress–Strain Data for a Range of Strain Rates

Advanced Engineering Materials, EarlyView.
This plot compares experimental tensile stress–strain curves (with 4 different strain rates) and corresponding modelled curves (obtained using the optimised sets of Voce and Miller–Norton parameter values shown). The inferred M‐N values, characterizing the creep, are very similar to those obtained via conventional creep testing.
S. Ooi, R. P. Thompson, T. W. Clyne
wiley   +1 more source

The Aging of Recycled Fibers [PDF]

, 1980
The object of this thesis is to study the aging of recycled paper, focusing on strength and optical properties. To observe the changes in these properties, the following experimental procedure was used.
Dubbeld, Martha M.
core   +1 more source

Constitutive Relation of Aluminum Bronze Material Commonly Used for the Threaded Ring of Downhole Tool Housing

Cejing jishu
In order to optimize the service performance and reliability of the threaded ring of petroleum logging tool under complex temperature conditions, this study focuses on QAL10-4-4 aluminum bronze and adopts a combination of experimental and modeling ...
WANG Shuihang, WANG Guanyu, LI Jingxiang, HOU Xueli, WANG Jingxiang, ZHOU Yutang, FAN Shuqin   +6 more
doaj   +1 more source

Direct Metal Deposition of Graphene–Ti28Nb35.4Zr Matrix Composites With Enhanced Mechanical, Corrosion, and Biocompatibility Properties for Bone Implants

Advanced Engineering Materials, EarlyView.
Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir, Jixing Lin, Yuncang Li, Li Zhu, Paul F. A. Wright, Cuie Wen   +5 more
wiley   +1 more source