Results 11 to 20 of about 87,865 (294)

Interlaboratory proficiency testing of tensile and flexural testing for cellulose based transformed board material [PDF]

International Journal of Metrology and Quality Engineering, 2012
Optimum safety and reliability can be achieved by coordinating an interlaboratory proficiency testing among different laboratories. Testing laboratories need to verify their test procedures and testing capability for reliable results.
Aydemir B., Fank S.
doaj   +1 more source

RETRACTED: Tensile testing of composite elastomer specimen [PDF]

E3S Web of Conferences
See the retraction notice E3S Web of Conferences 549, 00001 (2024), https://doi.org/10.1051/e3sconf ...
Minaev Andrey
doaj   +1 more source

A multifunctional rock testing system for rock failure analysis under different stress states: Development and application

Journal of Rock Mechanics and Geotechnical Engineering, 2022
The stress state in a rock mass is complex. Stress redistribution around underground excavation may lead to various failure modes, including compressive-shear, tensile-shear, and tensile failures.
Shucai Li, Jie Hu, Florian Amann, Liping Li, Hongliang Liu, Shaoshuai Shi, Pooya Hamdi   +6 more
doaj   +1 more source

Tensile properties and microstructure evolution during two-stage tensile testing of CoCrFeMnNi high-entropy alloy

Journal of Materials Research and Technology, 2020
The tensile properties of a CoCrFeMnNi high-entropy alloy, obtained by isothermal tensile testing and two-stage non-isothermal tensile testing, were compared.
Taesung Park, Jeoung Han Kim
doaj   +1 more source

Additive Manufacturing in Construction—Implementing Powder-Bed Fusion of Metals Using a Laser (PBF-LB/M) and Shape Optimization in the Construction Design Process

Engineering Proceedings, 2023
In this study, the implementation of the PBF-LB/M process into the construction design and building process was investigated. To this purpose, a tensegrity-tower was designed, planned, and built.
Johannes Diller, Christina Radlbeck, Dorina Siebert, Jakob Blankenhagen, Drilon Gubetini, Florian Oberhaidinger, Martin Mensinger   +6 more
doaj   +1 more source

Strain hardening exponent and strain rate sensitivity exponent of dual-phase steels at quasi-static strain rates during tensile testing

Cogent Engineering, 2023
The effects of quasi-static strain rates on the tensile properties of two commercial ferrite-martensite dual-phase DP 600 and DP 800 steels were investigated using strip-shaped samples.
W. Khraisat
doaj   +1 more source

Tensile Test For Arboform Samples [PDF]

ACTA Universitatis Cibiniensis, 2015
Abstract Petroleum-based plastic materials constitute a major environmental problem due to their low biodegradability and accumulation in various environments. Therefore, searching for novel biodegradable plastics is received particular attention.
Plavanescu (Mazurchevici), Simona, Quadrini, Fabrizio, Nedelcu, Dumitru   +2 more
openaire   +3 more sources

Damage Behavior of Sintered Fiber Felts

Metals, 2015
The reduction of aircraft noise is important due to a rising number of flights and the growth of urban centers close to airports. During landing, a significant part of the noise is generated by flow around the airframe.
Nicolas Lippitz, Joachim Rösler
doaj   +1 more source

Dynamic Tensile Testing of Needle-Punched Nonwoven Fabrics

Applied Sciences, 2020
The tensile testing of a needle-punched nonwoven fabric is presented. A high-sensitivity Split-Hopkinson Tensile Bar device was specifically designed for this purpose.
Francisca Martínez-Hergueta, Antonio Pellegrino, Álvaro Ridruejo, Nik Petrinic, Carlos González, Javier LLorca   +5 more
doaj   +1 more source

The development of a novel small ring specimen tensile testing technique

Ubiquity Proceedings, 2018
The use of small specimens in routine testing would reduce resource requirements, however, limitations exist due to concerns over size effects, manufacturing difficulties, uncertainties related to the application of representative loading conditions, and
J. Kazakeviciute, J.P. Rouse, C.J. Hyde
doaj   +1 more source