Results 241 to 250 of about 1,103,913 (306)

Practices, management, and typology of dromedary livestock systems and health constraints in southwestern Tunisia: The case of the Gafsa region. [PDF]

Vet Anim Sci
Sadraoui R, Khaldi S, Kallel I, Jaouad M.   +3 more
europepmc   +1 more source

Influence of Si Content and Milling Duration on the Microstructure and Mechanical–Tribological Properties of AlCoCrFeNiSi High‐Entropy Alloys

Advanced Engineering Materials, EarlyView.
Si‐doped AlCoCrFeNi high‐entropy alloys are synthesized by mechanical alloying to reveal the effect of Si content and milling time on phase evolution, microstructural refinement, and tribological behavior. A transition from FCC to BCC structure, significant grain refinement, and enhanced hardness and wear resistance are achieved, with the 4 at% Si ...
Mustafa Okumuş, Mehmet Emin Demir, Sercan Özpınar   +2 more
wiley   +1 more source

Development of <i>Saccharomyces cerevisiae</i> isobutanol production strain from osmotolerant and ethanol-producing industrial isolated yeast. [PDF]

Biotechnol Rep (Amst)
Thammapanyaphong N, Boonyanuwat M, Luengnaruemitchai A, Koonthongkaew J.   +3 more
europepmc   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

FORWARD: Dataset of a forwarder operating in rough terrain. [PDF]

Data Brief
Lundbäck M, Wallin E, Häggström C, Nyström M, Grönlund A, Richardson M, Jönsson P, Arnvik W, Hedström L, Fälldin A, Servin M.   +10 more
europepmc   +1 more source

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Correction: Primary choroidal lymphoma with extrascleral extension and bone marrow involvement: a case report. [PDF]

Front Med (Lausanne)
Frontiers Production Office.
europepmc   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

Editorial: Microbial degradation of agricultural waste. [PDF]

Front Microbiol
Tahir N, Pusztahelyi T.
europepmc   +1 more source

Lipidomic predictors of residual insulin production in adults with newly diagnosed type 1 diabetes. [PDF]

Metabolomics
Hostrup PE, Sulek K, Pociot F.
europepmc   +1 more source