Results 251 to 260 of about 371,296 (337)

Non-isothermal TGA study on the combustion reaction kinetics and mechanism of low-rank coal char

, 2018
Yingjie Hu, Zhiqiang Wang, Xingxing Cheng, Chunyuan Ma   +3 more
openalex   +2 more sources

Transvenous Coronary Sinus Lead Placement in Systemic Right Ventricle With D-TGA and Atrial Baffle. [PDF]

JACC Case Rep
Reyes JL, Feuerborn M, Shabbir A, Prisco A, Kalra R, Von Wald L, Benditt DG, Roukoz H.   +7 more
europepmc   +1 more source

Degradation Mechanisms in PEM Water Electrolysis: Diagnosis and Impact

Advanced Materials Technologies, EarlyView.
This review provides an analysis of degradation mechanisms in proton electrolyte membrane water electrolyzers (PEMWE), focusing on all key components. It discusses diagnostic and measurement techniques for evaluating degradation, less‐studied mechanisms, and an expert survey.
Annik Bernhardt, Katja Lange, Robert Göckeritz, Erik Grunwald, Angelika Hähnel, Alexander Müller, Volker Naumann, Sistan Rasuli, Wolfram Münchgesang, Bruno G. Pollet, Kerstin Witte‐Bodnar, Klemens Ilse   +11 more
wiley   +1 more source

Integrating Characterization, Kinetic, and Thermodynamic Analysis into Pacific Colombian Biomass Residues for Preliminary Bioenergy Assessment Via Coats–Redfern Modeling Under Single-Rate Tga Conditions

Diana Castro Mur, Diego Mauricio Yepes
openalex   +1 more source

Impact of Copper Ions on the Structuration of the Polydopamine Layer for the Functionalization of Graphene Nanoplatelets. [PDF]

ACS Omega
Barbe J, Alves Silva AE, Valero A, Guillot J, Philippe AM, Barborini E, Lamblin G.   +6 more
europepmc   +1 more source

Molecular Inks for the Development of Complex 3D In‐Mold Electronics

Advanced Materials Technologies, EarlyView.
Molecular inks (MINKs) enable the fabrication of thermoformed 3D circuits by decoupling the forming and metallization steps. Following thermoforming, intense pulsed‑light or thermal processing converts the patterned MINKs into complex 3D conductive tracks with improved stretchability and electrical performance, advancing low‑cost, high‑performance in ...
Mehal P. Kushalkar, Hiroshi Fukutani, Olga Mozenson, Jianying Ouyang, Liliana Gaburici, Bhavana Deore, Dayna Bennett, Chantal Paquet, Paul Trudeau, Loleï Khoun, Nicolas Milliken, Olivier Ferrand, Julie Ferrigno, Xiangyang Liu, Arnold J. Kell   +14 more
wiley   +1 more source

Effects of nucleation on solvate and polymorph control - evaporative crystallization of taltirelin. [PDF]

RSC Adv
Nguyen DLT, Kim J, Kim KJ, Ulrich J.
europepmc   +1 more source

Additive Manufacturing of Ni‐Based Thermoelectric Materials for Waste Heat Recovery

Advanced Materials Technologies, EarlyView.
Thermoelectric generators convert waste heat into electricity but are constrained by conventional fabrication. Here, laser powder bed fusion enables direct printing of customised n‐type Cu60Ni40 and p‐type Ni90Cr10 legs. The assembled module achieves 0.8% efficiency at ΔT = 419 K, demonstrating scalable additive manufacturing of eco‐friendly, design ...
Karolin Amstein, Aayush Dobhal, Heiko Reith, Ran He, Julia Kristin Hufenbach, Kornelius Nielsch, Pingjun Ying   +6 more
wiley   +1 more source

Morris B. Bender (1905-1983). [PDF]

J Neurol
Larner AJ.
europepmc   +1 more source