Results 201 to 210 of about 41,270 (311)

Experimental and Numerical Modal Analysis of Composite Sandwich Structures Using Surfboards as Model Systems

Advanced Engineering Materials, EarlyView.
This article presents an experimental and numerical modal investigation of composite sandwich structures using surfboards as model systems. By comparing different core materials and reinforcement strategies, the study demonstrates how local stiffeners influence vibrational response and introduce characteristic modal features, highlighting modal ...
Brett Connellan, Luca Lomazzi, Mathis Mercier, Kara Stark, Marc in het Panhuis   +4 more
wiley   +1 more source

Experimental mechanician for plate lattice metamaterial discovery. [PDF]

Nat Commun
Hu S, Li H, Lu W, Xie T, Ding X, Zhang X, Shi X, Peng Z, Cao X.   +8 more
europepmc   +1 more source

Advanced Electron Microscopy and Microcomputed Tomography Analysis of Single‐Crystal Ni‐Base Superalloys After Short‐Term Multiaxial Creep

Advanced Engineering Materials, EarlyView.
This work studies the anisotropic behavior of circular notched tensile specimens of Ni‐base superalloy single crystals during high‐temperature tensile creep along [001], [110], and [111]. Correlative scale‐bridging imaging of specimens reveals early rupture along [110] because 1) plastic deformation proceeds faster at notch center; 2) more (brittle ...
Leonardo Agudo Jácome, Lijie Cao, Christoph Somsen, Johannes Boes, René Hesse, Werner Theisen, Gunther Eggeler   +6 more
wiley   +1 more source

Simulation-Based X-Ray Spectrum Optimization for Dose Enhancement in X-Ray-Induced Photodynamic Therapy with NaLuF₄:20% Gd, 15% Tb³⁺ Nanocrystals. [PDF]

Bioengineering (Basel)
Li W, Gao P, Li R, Liu T, Wang Z, Zhang W, Lu H, Liu Y, Rong J.   +8 more
europepmc   +1 more source

A Study of Optimal Guide Procedure in Building Using Agent Simulation and Optimal Location Problem

Transactions of the Institute of Systems, Control and Information Engineers, 2015
Keita Sugiura, Masahiro Arakawa
openaire   +2 more sources

Defect Evolution and Mechanical Performance of Fused Filament Fabrication‐Manufactured 17‐4PH Stainless Steel Revealed by X‐Ray Computed Tomography

Advanced Engineering Materials, EarlyView.
X‐ray computed tomography reveals how process‐induced defects evolve from green to sintered states in Fused Filament Fabrication (FFF)‐manufactured 17‐4PH stainless steel. Internal porosity, weakest cross‐sections, and fracture locations show strong correlation with tensile performance, demonstrating the potential of computed tomography (CT)‐based ...
György Ledniczky, Márk Sárközi, Ibolya Zsoldos, Zoltán Weltsch   +3 more
wiley   +1 more source

Graph-theoretic analyses of saturation fraction of repulsive dopants in solid solutions. [PDF]

Sci Rep
Kubo A, Abe Y.
europepmc   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

Scenario-Based Simulation Modeling for Performance and Efficiency Improvement in an Ultrasonography Department. [PDF]

Healthcare (Basel)
Saraçoğlu İ.
europepmc   +1 more source

Active Corrosion Protection of Sintered AA7075 Aluminum Alloy via Mn Powder Addition

Advanced Engineering Materials, EarlyView.
AA7075 containing Mn‐rich particles is fabricated via spark plasma sintering using AA7075 and Mn powders. Corrosion resistance is evaluated through dip‐and‐dry tests using 0.1 M NaCl (pH 6.0), and mass loss decreases with increasing Mn addition. Mn‐rich particles function as a source of Mn ions, and formation of Mn‐accumulation films on Cu‐containing ...
Ko Ebina, Masashi Nishimoto, Izumi Muto
wiley   +1 more source