Results 221 to 230 of about 2,008,385 (296)

Nitride MXenes Beyond Carbides: Bridging the Gap Between Computational Prediction and Experimental Realization

Advanced Functional Materials, EarlyView.
Nitride MXenes remain constrained by a persistent gap between computational prediction and experimental realization. This Review identifies the thermodynamic, kinetic, and chemical barriers limiting their synthesis, critically evaluates emerging fabrication routes, and proposes a multidimensional computational‐experimental framework to accelerate the ...
Naresh Varnakavi, Masoud Soroush
wiley   +1 more source

Photoinduced Interfacial Electronic Modulation in Fe2O3‐BiVO4 Heterostructures for Enhanced Photo‐Assisted Zn‐Air Batteries

Advanced Functional Materials, EarlyView.
Light irradiation activates the Fe2O3‐BiVO4 heterostructure, enabling efficient solar‐electrochemical coupling in zinc‐air batteries. The built‐in electric field drives directional charge separation, guiding photoelectrons toward oxygen reduction sites and accumulating holes for oxygen evolution, thereby reducing polarization and enhancing discharge ...
Yili Liu, Zhenjiang Du, Enming Liu, Hongzhou Dong, Jianguang Feng, Beili Pang, Lifeng Dong, Liyan Yu   +7 more
wiley   +1 more source

Out‐of‐Plane Strain‐Decoupled Architecture for High‐Fill‐Factor Stretchable OLED Displays

Advanced Functional Materials, EarlyView.
A vertically decoupled multilayer SOLED architecture separates emissive pixel islands from deformable interconnects, allowing low‐modulus elastomeric layers to accommodate applied strain and suppress strain transfer to the OLED region. This design, combined with transparent hybrid encapsulation, enables a high fill factor (∼75%), stretchability ...
Young Hyun Son, Kyung Cheol Choi, Jeong Hyun Kwon   +2 more
wiley   +1 more source

Anomalous thermal diffusivity in underdoped YBa₂Cu₃O_6+x. [PDF]

Proc Natl Acad Sci U S A, 2017
Zhang J, Levenson-Falk EM, Ramshaw BJ, Bonn DA, Liang R, Hardy WN, Hartnoll SA, Kapitulnik A.   +7 more
europepmc   +1 more source

Biodegradable 3D‐Printable and Coatable Antifouling Composites for Marine Applications

Advanced Functional Materials, EarlyView.
Marine biofouling damages submerged surfaces and raises greenhouse gas emissions. Biodegradable antifouling biocomposites were developed by hot‐mixing beeswax, Tween 80, and calcium stearate or stearic acid. Adjusting the component ratio enables processing via hot‐pressing, 3D‐printing, or dip‐coating.
Gabriele Corigliano, Lorenzo Ravelli, Martina Nardi, Ruowen Tu, Elena Bellini, Valerio Isa, Carlo Filippeschi, Roberta Finazzi, Luca Ceseracciu, Niloofar Paknezhad, Vincenzo Scribano, Paolo Galli, Silvia Lavorano, Simone Montano, Barbara Mazzolai, Marco Contardi, Pietro Cataldi, Athanassia Athanassiou   +17 more
wiley   +1 more source

Polymer Side‐Chain Electronic Effects Regulating Solvation Sheath for Low‐Temperature and High‐Voltage Lithium Metal Batteries

Advanced Functional Materials, EarlyView.
This work reveals the influence of polymer side‐chain electronic effects on the Li+ solvation sheath in gel polymer electrolytes. Electron‐donating side chains induce the strong Li+ coordination and FDMA‐dominated solvation, impeding Li+ desolvation, whereas electron‐withdrawing side chains weaken Li+ coordination, facilitating anion‐rich solvation and
Xianbin Wu, Zhenxiang Zhu, Haotian Yang, Dayao Zhang, Zhen Geng, Cunman Zhang, Mingzhe Xue, Jian Wang   +7 more
wiley   +1 more source

Full‐Field Damage Monitoring in Architected Lattices Using In situ Electrical Impedance Tomography

Advanced Functional Materials, EarlyView.
In situ electrical impedance tomography (EIT) turns 3D‐printed, CNT‐infused architected lattices into full‐field damage‐imaging systems. Tunable Voronoi‐based geometries act as active sensing architectures, enabling conductivity maps to detect early‐stage damage and localise sequential ligament fracture before catastrophic failure.
Akash Deep, Andrea Samore, Alistair McEwan, Andrew McBride, Shanmugam Kumar   +4 more
wiley   +1 more source

Lewis Acid Site Engineering in MOF‐Derived Aluminum Oxide/Carbon Composites for Dechlorination of Waste Plastic Pyrolysis Oil

Advanced Functional Materials, EarlyView.
Controlled carbonization of an Al‐MOF partially decomposes its linkers, exposing coordinatively unsaturated Al centers within an oxide/carbon composite. The resulting Lewis acid sites, rather than surface area, govern organochlorine capture: the composite removes chemically diverse organochlorines from waste plastic pyrolysis oil, outperforms a ...
Seong Cheon Kim, Byeongju Jeon, Suk Hyun Lim, Eun Hee Kwon, Nam Sun Nho, Siyoung Q. Choi, Jeasung Park   +6 more
wiley   +1 more source

A New Strategy for Creating Quantum Light Emitters Via Post‐Growth Hydrogen‐Ion Irradiation of III‐V Nanowires

Advanced Functional Materials, EarlyView.
A post‐growth method is demonstrated to realize energy‐tunable quantum emitters in GaAs/GaAsN/GaAs core–multishell nanowires on a Si substrate. By combining the N‐induced bandgap reduction with H‐ion irradiation, the GaAsN potential landscape is engineered, enabling isolated, narrow emission lines that function as single‐photon sources with g(2)(0) ∼ 0.
Akant Sagar Sharma, Paolo De Vincenzi, Nadine Denis, Francesca Santangeli, Riccardo Pallucchi, Harikrishnan Gopalakrishnan, Elena Blundo, Antonio Polimeni, Marco Felici, Fumitaro Ishikawa, Marta De Luca   +10 more
wiley   +1 more source

Halide Composition Controls Phase Morphology and Device Specific Performance in Perovskite Photovoltaics and Light Emitting Diodes

Advanced Functional Materials, EarlyView.
We demonstrate that halide composition determines phase morphology, governing distinct operating mechanisms in mixed halide perovskites. Phase segregating 75% Br compositions enhance solar cell performance, whereas intrinsically phase‐separated 95% Br compositions provide stable light emitting diodes.
Tal Binyamin, Stav Rahmany, Anat Shvets, Hadar Shema, Elad Gross, Ido Hadar, Lioz Etgar   +6 more
wiley   +1 more source