Results 151 to 160 of about 905,279 (309)

A Return to Normality: A Descriptive Qualitative Interview Study Exploring the Patient Experience of Gout Flare Resolution

Arthritis Care &Research, EarlyView.
Objective Although the definition of a gout flare is well established, the state of gout flare resolution has not yet been defined. This study aimed to explore patients’ experiences and perceptions of gout flare resolution. Methods Semistructured interviews were conducted with 24 people with gout, guided by open‐ended questions exploring their ...
Sarah Stewart, Anne Horne, Angelo Gaffo, Lisa K. Stamp, N. Lawrence Edwards, Nicola Dalbeth   +5 more
wiley   +1 more source

Integrating active thermal mass strategies in responsive buildings

, 2010
This thesis was submitted for the degree of Engineering Doctorate and awarded by Brunel University.Thermal mass can be used in buildings to reduce the need for and dependence on mechanical heating and cooling systems whilst maintaining environmental ...
Warwick, David James
core  

Analytical solution of one-dimensional electroosmotic consolidation considering the thermal effect

Shuiwen dizhi gongcheng dizhi
In recent years, electro-osmotic method is an effective foundation treatment method for dredged silt; however, few studies have focused on the influence of temperature on the electro-osmotic consolidation. To explore the influence of temperature field on
Qi LU, Ganbin LIU, Yongzheng MA
doaj   +1 more source

Thermal Effect on Thin-Film Formation of the Polymer Sheets by the CO₂ Laser with the Copper Base. [PDF]

Polymers (Basel), 2022
Kameyama N, Yoshida H.
europepmc   +1 more source

Mechanochemical Synthesis and Characterization of Nanostructured ErB4 and NdB4 Rare‐Earth Tetraborides

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
ErB4 and NdB4 nanostructured powders are produced by mechanochemical synthesis. 5 h mechanical alloying and 4 M HCl acid leaching are used in the production. ErB4 and NdB4 powders exhibit maximum magnetization of 0.4726 emu g−1 accompanied with an antiferromagnetic‐to‐paramagnetic phase transition at about TN = 18 K and 0.132 emu g−1 with a maximum at ...
Burçak Boztemur, Faruk Kaya, Bora Derin, Mustafa Lütfi Öveçoğlu, Ju Li, Duygu Ağaoğulları   +5 more
wiley   +1 more source

Thermal Effect during Laser-Induced Plasmonic Heating of Polyelectrolyte-Coated Gold Nanorods in Well Plates. [PDF]

Nanomaterials (Basel), 2023
Jiracheewanun S, Cortie MB, Pissuwan D.
europepmc   +1 more source

Revisiting Stability Criteria in Ball‐Milled High‐Entropy Alloys: Do Hume–Rothery and Thermodynamic Rules Equally Apply?

Advanced Engineering Materials, Volume 27, Issue 6, March 2025.
The stability criteria affecting the formation of high‐entropy alloys, particularly focusing in supersaturated solid solutions produced by mechanical alloying, are analyzed. Criteria based on Hume–Rothery rules are distinguished from those derived from thermodynamic relations. The formers are generally applicable to mechanically alloyed samples.
Javier S. Blázquez, Alejandro F. Manchón‐Gordón, Antonio Vidal‐Crespo, Rafael Caballero‐Flores, Jhon J. Ipus, Clara F. Conde   +5 more
wiley   +1 more source

Thermal response testing through the chalk aquifer

, 2013
Thermal conductivity of the ground is an important parameter in the design of ground energy systems, which have an increasing role to play in providing renewable heat to the built environment.
Powrie, W., Powrie, W, Roberts, T, Loveridge, F, Holmes, G, Roberts, T., Holmes, G., Loveridge, F.   +7 more
core   +1 more source

The combination of eddy thermal effect of biodegradable magnesium with immune checkpoint blockade shows enhanced efficacy against osteosarcoma. [PDF]

Bioact Mater, 2023
Ge J, Yang N, Yang Y, Yu H, Yang X, Wang Y, Wang T, Cheng S, Wang Y, Han Z, Teng Y, Zou J, Yang H, Cheng L.   +13 more
europepmc   +1 more source

Characterization of Defect Distribution in an Additively Manufactured AlSi10Mg as a Function of Processing Parameters and Correlations with Extreme Value Statistics

Advanced Engineering Materials, EarlyView.
Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt, Varma Kvvssn, Hossein Laieghi, Zia Uddin, Peyman Ansari, E. Kıvanç Sadak, Can Barış Toprak, Hüseyin Kızıl, Enrico Salvati   +8 more
wiley   +1 more source