Results 171 to 180 of about 764,055 (296)

Combined Process‐ and Phase‐Field‐Simulation to Predict the Microstructure of Single‐Crystal Ni‐Based Superalloys

Advanced Engineering Materials, EarlyView.
A combined finite element and phase‐field approach predicts the evolution of microstructure during the directional solidification of Ni‐based superalloys. The model reveals how withdrawal rate, temperature gradient, and wall thickness control the dendrite spacing, highlighting the strong effect of surface regions in thin sections where dendrite growth ...
Sean Böhm, André B. Baldissera, Rainer Völkl, Uwe Glatzel   +3 more
wiley   +1 more source

Thermophysical Properties of the Desulphurization Slags With Various CaS and CaO/Al2O3 Ratio

Advanced Engineering Materials, EarlyView.
This article investigates how CaS content and the CaO/Al2O3 ratio influence the thermophysical properties of desulphurization slags. Using experimental measurements and thermodynamic simulations, this study reveals complex effects on viscosity, surface tension, and density, providing new insight into slag structure and phase behavior under ...
Eldar Salpagarov, Matheus Roberto Bellé, Anton Yehorov, Julia Richter, Olena Volkova   +4 more
wiley   +1 more source

Thermal Modification’s Influence on the Color of Tectona grandis L.f. Sapwood to Resemble Heartwood

BioResources
The commercial value of teak wood is associated with its heartwood, which has a naturally darker color than sapwood. To reduce this color disparity, thermal modification can be used to homogenize the color between sapwood and heartwood by minimizing ...
Ariany Mendes Cruz, Theonizi Angélica Silva Albuês, Daiane de Moura Borges Maria, João Paulo Sardo Madi, Jéssica Sabrina da Silva Ferreira, Udson de Oliveira Barros Jr, Aylson Costa Oliveira, Djeison Cesar Batista, Barbara Luísa Corradi Pereira   +8 more
doaj  

Characterization of a Recyclate‐Based MgO‐Steel Composite As‐Sintered Inert Anode Candidate After Exposure to Cryolite Electrolysis

Advanced Engineering Materials, EarlyView.
Carbon‐free inert anodes are essential for decarbonizing aluminum electrolysis. This study investigates a recyclate‐based MgO‐316L steel composite anode tested under galvanostatic Hall–Héroult conditions in cryolite at 1000°C. Microstructural analysis reveals selective MgO fluorination, spinel and oxide layer formation, electrolyte infiltration, and ...
Serhii Yaroshevskyi, Alexander Adamczyk, Nora Brachhold, Gert Schmidt, Jana Hubálková, R. Gumeniuk, Alexandros Charitos, Christos G. Aneziris   +7 more
wiley   +1 more source

Powder Optimization Strategies for Binder Jetting Printing of BaTiO3 and Ba0,6Sr0,4TiO3 Ceramics

Advanced Engineering Materials, EarlyView.
Powder optimization is investigated to enable binder jetting of BaTiO3 and Ba0.6Sr0.4TiO3 ferroelectric ceramics. The antagonistic relationship between flowability and binder compatibility is addressed through binder impregnation of granulated powders and fumed silica addition to fine powders.
Fanny Pruvost, Lionel Presmanes, Soléna Colin, Marie Vidal, Sophie Guillemet‐Fritsch   +4 more
wiley   +1 more source

Influence of an Oxygen‐Free Atmosphere on Diamond‐Single‐Grain Scratching of Ti–6Al–4V

Advanced Engineering Materials, EarlyView.
Single‐grain scratching of Ti–6Al–4V is investigated under controlled, oxygen‐free, and ambient atmospheres using a novel experimental setup with in situ high‐speed imaging. The approach enables direct observation of chip formation and adhesion under suppressed oxidation.
Berend Denkena, Benjamin Bergmann, Michael Zenger   +2 more
wiley   +1 more source

Population of Nonmetallic Inclusions in Liquid High‐Silicon Electrical Steel in Contact With MgO–C Refractories Based on Recyclates and Environmentally Friendly Binders

Advanced Engineering Materials, EarlyView.
The formation of nonmetallic inclusions (NMIs) was investigated in this study, carrying out immersion tests for 30 min at a temperature of 1600°C with liquid high‐silicon electrical steel (Si ≈ 3 mass‐%) and different MgO–C refractories. Conventional MgO–C refractories were considered, as well as MgO–C refractories containing MgO–C recyclate and ...
Lukas Neubert, Matheus Roberto Bellé, Florian Kerber, Dinesh Kumar Gunasekar, Hans‐Jörn Weddige, Christos G. Aneziris, Olena Volkova   +6 more
wiley   +1 more source

Al–Cu Composite Casting of Laser‐Deoxidized Copper: Bonding, Interfacial Chemistry, and Thermal Conductivity

Advanced Engineering Materials, EarlyView.
This study investigates laser‐based oxide removal of Cu inserts in oxygen‐free conditions and examines long‐term oxidation kinetics and surface chemistry under different atmospheres via X‐ray photoelectron spectroscopy. Al–Cu compound casting with differently oxidized surfaces is performed, and intermetallic phase formation, morphology, and thermal ...
Timon Steinhoff, Finn‐Lennard Janthur, Sascha Zimmermann, Sarah Seffer, Jörg Hermsdorf, René Gustus, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Christian Klose   +9 more
wiley   +1 more source

Assessing Altered Coating Adhesion on Plasma‐Deoxidized Surfaces Under Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
This study demonstrates the effectiveness of atmospheric pressure plasma pretreatment in modifying silicon and stainless steel surfaces to improve adhesion. Argon‐hydrogen plasma increases surface roughness and improves adhesion strength, whereas pure argon results in smoother surfaces and structural changes.
Selina Raumel, Lara Kuhr, Khemais Barienti, Sebastian Herbst, Florian Nürnberger, Hans Jürgen Maier, Marc C. Wurz   +6 more
wiley   +1 more source

Accelerated Aging Effect on Volatile Organic Compound Emissions from Thermally Treated Spruce Wood. [PDF]

Materials (Basel)
Bubeníková T, Kačík F, Darabošová A, Čabalová I.   +3 more
europepmc   +1 more source