Results 131 to 140 of about 314,980 (299)
Arthritis Care &Research, EarlyView.Objective Although the definition of a gout flare is well established, the state of gout flare resolution has not yet been defined. This study aimed to explore patients’ experiences and perceptions of gout flare resolution. Methods Semistructured interviews were conducted with 24 people with gout, guided by open‐ended questions exploring their ...
Sarah Stewart +5 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Predicting extreme defects in additive manufacturing remains a key challenge limiting its structural reliability. This study proposes a statistical framework that integrates Extreme Value Theory with advanced process indicators to explore defect–process relationships and improve the estimation of critical defect sizes. The approach provides a basis for
Muhammad Muteeb Butt +8 more
wiley +1 more source
Thermal response test [Elektronisk resurs] : in situ measurements of thermal properties in hard rock [PDF]
, 1998 In-situ determination of thermal properties in bedrock is important for the sizing of larger BTES systems. In-situ values of thermal conductivity may reduce required borehole length up to 30%.
Gehlin, Signhild,
core
Advanced Engineering Materials, EarlyView.This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo +3 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.In this review, the current state of light‐assisted 3D printing as it pertains to engineering musculoskeletal tissues including bone, cartilage, skeletal muscle, tendon, and ligaments is summarized. Common printing techniques, photoreactive materials, and study design choices are compiled and reviewed.
Meagan Morgan, Bin Zhang, Roger Narayan
wiley +1 more source
Advanced Engineering Materials, EarlyView.A flexure‐based variable stiffness structure is developed by integrating phase‐change modulation and adhesive interfacial locking of gallium. The design enables a wide stiffness variability, transitioning from soft, flexible behavior to rigid, load‐supporting performance.
Sungjin Kim +2 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Geometry‐driven thermal behavior in wire‐arc additive manufacturing (WAAM) influences microstructural evolution during nonequilibrium solidification of a chemically complex Fe–Cr–Nb–W–Mo–C nanocomposite system. By comparing different deposits configurations, distinct entropy–cooling rate correlations, segregation, and carbide evolution are revealed ...
Blanca Palacios +5 more
wiley +1 more source
Two-Dimensional Finite Element Ablative Thermal Response Analysis of an Arcjet Stagnation Test [PDF]
, 2011 The finite element ablation and thermal response (FEAtR, hence forth called FEAR) design and analysis program simulates the one, two, or three-dimensional ablation, internal heat conduction, thermal decomposition, and pyrolysis gas flow of thermal ...
Dec, John A. +2 more
core +1 more source
Performance Analysis of Abradable Coating Systems for Aircraft Gas Turbines
Advanced Engineering Materials, EarlyView.Three CoNiCrAlY/YSZ/MgAl2O4 abradable liner configurations on a nickel‐superalloy are evaluated by thermal‐gradient cycling and incursion tests. Laser ablation of the bondcoat and/or Y2O3‐stabilized ZrO2 (YSZ) intermediate layer increases mechanical interlocking and bonding for thick topcoats.
Hanna Heyl +4 more
wiley +1 more source
Advanced Engineering Materials, EarlyView.Mg–Zn composites with a thickness of 0.21 mm were fabricated using roll bonding of a kirigami‐patterned Mg alloy inlay within a Zn matrix. Thermal activation following this process led to the formation of tailored intermetallic structures, which provided the composite with enhanced flexural strength.
Yaroslav Frolov +4 more
wiley +1 more source