Results 121 to 130 of about 27,171 (260)

Inverse Identification of Energy‐Dependent Laser Absorptivity in NiTi Laser Powder‐Bed Fusion via Calibrated Melt Pool Simulation

Advanced Engineering Materials, EarlyView.
A combined experimental–computational framework identifies energy‐dependent laser absorptivity for NiTi in laser powder‐bed fusion, applicable to conduction and transition modes. Single‐track experiments and thermofluid smoothed particle hydrodynamics simulations are coupled through inverse analysis of melt pool geometry.
Mohamadreza Afrasiabi, Hadi Moutablaleh, Ignatius A. Setiawan, Mehrshad Mehrpouya   +3 more
wiley   +1 more source

Comparison of Triply Periodic Minimal Surface Energy Absorbers Under Uniaxial Compressive Loading

Advanced Engineering Materials, EarlyView.
This study investigates LCD 3D printed Triply Periodic Minimal Surface (TPMS) structures as mechanical energy absorbers. By comparing various base designs and layered combinations under uniaxial compression, it identifies that a Diamond‐Gyroid sandwich structure offers superior performance.
Sergej Grednev, Noah‐Lean Roschlaub, Anne Jung   +2 more
wiley   +1 more source

Triple Junctions as Dislocation‐Like Defects: The Role of Grain Boundary Crystallography Revealed by Experiment and Atomistic Simulation

Advanced Engineering Materials, EarlyView.
Grain boundary triple junctions are an essential ingredient of the microstructure of polycrystalline materials. In this study, a triple junction is observed using atomic‐resolution scanning transmission electron microscopy and characterized. Computer simulations reveal that the junction has a dislocation character that is determined by the joining ...
Tobias Brink, Saba Saood, Peter Schweizer, Jörg Neugebauer, Gerhard Dehm   +4 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

A Practical Noise2Noise Denoising Pipeline for High‐Throughput Raman Spectroscopy

Advanced Engineering Materials, EarlyView.
A lightweight and reproducible denoising pipeline for high‐throughput Raman spectroscopy is introduced, based on a 1D convolutional autoencoder trained with a Noise2Noise strategy. Using only repeated short‐exposure acquisitions, the method suppresses stochastic noise without reference spectra, enabling reliable spectral reconstruction while preserving
David Martin‐Calle, Cesar Alvarez‐Llamas, Vincent Motto‐Ros, Christophe Dujardin, Jérémie Margueritat, David Rodney   +5 more
wiley   +1 more source

Design and Analysis of Compression–Torsion Coupling Metamaterials Using the Golden Section Method

Advanced Engineering Materials, EarlyView.
A novel compression–torsion metamaterial is engineered using inclined rods and symmetry breaking. To optimize its torsional performance, the golden section method is employed. The mechanical response of the metamaterial is validated through both numerical analysis and experimental validation.
Amirhossein Hassani, Sara Bagherifard
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Hybrid Metal–Carbon Ink for Printed Stretchable Temperature Sensors

Advanced Engineering Materials, EarlyView.
We prepare conductive inks for temperature sensing with silver flakes and carbon or graphite flakes in a silicone elastomer matrix. Silver dominates the temperature‐dependent conductivity, while the carbon filler network ensures the stability of the conductive pathways and retains function under strain.
Makara Lay, Xue Bai, Thomas Kister, Tobias Kraus   +3 more
wiley   +1 more source

Continuous Stiffness Graded Metal–Ceramic Femoral Stems: UMAT‐Based Design and Finite Element Assessment

Advanced Engineering Materials, EarlyView.
Functionally graded metal–ceramic femoral stems are engineered through continuous UMAT‐based stiffness tailoring, eliminating discrete material interfaces while enhancing biomechanical compatibility. Low‐index power‐law gradation optimizes load transfer, reduces stress shielding, and controls implant–bone micromotion, highlighting a materials‐design ...
Rihem Nouira, Sameh Elleuch, Hanen Jrad
wiley   +1 more source

New AI‐Assisted Approach for Expanding the Solution Space: Application to Lattice Structure Design

Advanced Engineering Materials, EarlyView.
This work introduces an innovative framework for designing structured materials by ex panding the design space through reparameterization of qualitative variables into continuous structural descriptors. Combined with machine‐learning‐based prediction and multi‐objective optimization, the approach enables the discovery of novel lattice architectures ...
G. H. Gahimbare, Y. Beideler, D. Chune, R. De Guio, T. Roland, H. Chibane   +5 more
wiley   +1 more source