Results 11 to 20 of about 39,463 (241)
Optimization of Marine Medium Speed Diesel Engine Performance based on Multi-Injector System [PDF]
E3S Web of Conferences, 2021 Multi-injector system is potential to improve thermal efficiency and NOx emission of diesel engine at the same time. In order to optimize the combustion and emission of Marine medium speed diesel engine, the engine combustion with a multi-injector system
Liu Dai +4 more
doaj +1 more source
Rekayasa Mesin, 2022 The contact surface of thermal spray significantly affected bonding strength and coating elasticity. This work aimed to evaluate the effects of contact surface conditions characterised by substrate surface profile and spray pressure on the bonding and ...
Nurul Muhayat +5 more
doaj +1 more source
Study on high-speed electric motor cooling with oil spray
e-Prime: Advances in Electrical Engineering, Electronics and Energy, 2023 The transportation sector is experiencing quick electrification to pave the way to carbon-neutral society, which poses great challenges to the thermal management technologies for the motor as they are expected to be more and more powerful.
Xuehui Wang, Yuying Yan, Ying Li
doaj +1 more source
JIIS: Jurnal Ilmiah Ibnu Sina, 2021 Plasma jet non thermal dapat digunakan sebagai penyembuhan luka namun pengontrolan yang kurang tepat dapat menyebabkan akumulasi reactive oxygen spesies (ROS).
Ratih Arum Astuti +6 more
doaj +3 more sources
Experimental Study on Spray Cooling Heat Transfer of LN2 for a Large Area
Energies, 2023 Spray cooling has been considered one of the most promising thermal control methods of high-heat flux devices. Most of the spray cooling research focuses on electronic components as the main application object to achieve higher heat dissipation heat flow
Jinhong Zhao +4 more
doaj +1 more source
Review of Functionally Graded Thermal Sprayed Coatings
Applied Sciences, 2020 The paper briefly describes major thermal spray techniques used to spray functionally graded coatings such as atmospheric plasma spraying, high velocity oxy-fuel spraying, suspension and solution precursor plasma spraying, and finally low and high ...
Leszek Łatka +5 more
doaj +1 more source
Nihon Kikai Gakkai ronbunshu, 2021 Water spray is used for cooling intake air of gas turbine in thermal power plant. It is necessary to reduce the amount of residual droplets by optimizing the spray amount to keep the plant in good condition.
Katsuhiko SUGITA +5 more
doaj +1 more source
Investigation of the gamma shielding efficiency reduction by depositing PbO and MnO2 composition on various types of substrates [PDF]
Nuclear Technology and Radiation Protection, 2023 In this study, a PbO, MnO2, PbO + MnO2 thin film (nano layer) was deposited onto a microscope glass, indium tin oxide glass, and aluminum with thicknesses 0.1 mm and 0.5 mm substrate, samples were prepared by the thermal spray technique.
Alhamdi Walat Abdulqader +1 more
doaj +1 more source
A Comparative Study of the Life Cycle Inventory of Thermally Sprayed WC-12Co Coatings
MetalsIn this research, a life cycle inventory (LCI) is developed for tungsten carbide–cobalt (WC-Co) coatings deposited via atmospheric plasma spray (APS), high-velocity oxy-fuel (HVOF), and cold gas spray (CGS) techniques.
Edwin Rúa Ramirez +4 more
doaj +1 more source
Coatings for Hydro Turbine Applications: A Materials Perspective
MetalsCorrosion- and wear-resistant coatings are widely applied to hydro-turbine runners through thermal spray and cladding processes to enhance component efficiency and structural integrity by mitigating material loss during operation.
Rodolpho Fernando Vaz +3 more
doaj +1 more source