Results 61 to 70 of about 194,352 (287)
Огляд сучасного стану і перспектив розвитку газотермічних способів нанесення покриття [PDF]
, 2011 Conducted review on materials of international organization of International Thermal Spray Association and International Thermal Spray Conference and Exposition ITSC-2010 the modern state of gas-thermal methods of overcoating.
Корж, В. М. +2 more
core
Material Issues in Layered Forming [PDF]
, 1993 A brief overview of key issues in layered thermal processing is given. Incremental sintering and layered fusion ofpowder and molten droplets are discussed.
Amon, Christina +6 more
core +1 more source
Advanced Functional Materials, EarlyView.This work demonstrates the successful integration of a phenanthroline‐based 2D COF with MnI catalytic sites into a catholyte‐free membrane‐electrode‐assembly cell for CO2 electroreduction. The crystalline COF actively suppresses Mn⁰–Mn⁰ dimerization, achieving a turnover frequency of 617 h⁻¹ at 2.8 V (full‐cell potential), and enabling stable operation.
Laura Spies +8 more
wiley +1 more source
Reduction of nitrogen oxides by injection of urea in the freeboard of a pilot scale fluidized bed combustor [PDF]
, 1989 The ‘thermal deNOx’ process using urea has been investigated in a 1 MW fluidized bed combustor. NOx reductions of up to 76% were obtainable by using this method. The experimental results show that urea is at least as active as NH3, which is commonly used
Bramer, Eduard A. +2 more
core +3 more sources
Advanced Functional Materials, EarlyView.Shellac, a centuries‐old natural resin, is reimagined as a green material for flexible electronics. When combined with silver nanowires, shellac films deliver transparency, conductivity, and stability against humidity. These results position shellac as a sustainable alternative to synthetic polymers for transparent conductors in next‐generation ...
Rahaf Nafez Hussein +4 more
wiley +1 more source
Demonstrating circularity in thermal spraying: Converting waste to wealth
Materials Today SustainabilityTypically, 40–60 % of the injected powder feedstock in most thermal spray processes ends up as overspray waste and is a prominent technology drawback.
Rahul Jude Alroy +7 more
doaj +1 more source
Effervescent Breakup and Combustion of Liquid Fuels: Experiment and Modelling [PDF]
, 2014 Tato práce se zaměřuje na oblast effervescentních sprejů a jejich aplikace na kapalné spalování s důrazem na průmyslové spalovací komory. Oba aspekty – modelování a experiment – jsou řešeny.
Broukal, Jakub
core
Modelling of gas permeation through ceramic coatings produced by thermal spraying
, 2008 An analytical model has been developed for simulation of gas permeation through thermal spray coatings, and for prediction of the permeability. The model is based on a geometrical representation of the coating microstructure.
Clyne, T.W., Golosnoy, I.O., Paul, S.
core +1 more source
3D‐Printed Sulfur‐Derived Polymers With Controlled Architectures for Lithium‐Sulfur Batteries
Advanced Functional Materials, EarlyView.Rheology‐guided formulation design for direct ink writing enables the fabrication of 3D sulfur copolymer cathodes with controlled architectures for lithium‐sulfur batteries. The printed electrodes exhibit multiscale porosity and high sulfur utilization, delivering enhanced electrochemical performance compared to conventional cast electrodes.
Bin Ling +7 more
wiley +1 more source
Current Status of Application of Fractal Theory and Methods in Thermal Spray Coating Research [PDF]
Cailiao BaohuThermal spraying technology is one of the key supporting technologies of remanufacturing, and the heterogeneous interface between thermal spray coating and substrate has a significant impact on the coating performance.
WANG Rui, WANG Hai, LI Jiaqi, WANG Haidou, SUN Xiaofeng, MA Guozheng, LIU Jian, GUO yongming
doaj +1 more source