Results 91 to 100 of about 16,849 (243)

Thermoplastic Dielectric Coatings for Flexible Electrodynamic Dust Shields: Structural and Functional Performance

Advanced Materials Interfaces, EarlyView.
Thermoplastic attachment is introduced as a scalable surface coating strategy to improve the durability and dielectric reliability of flexible electrodynamic dust shields. By embedding chemically modified reduced graphene oxide (CMrGO) electrodes within thermoplastic laminates, mechanical degradation, abrasion damage, and vacuum‐induced electrical ...
Ide E. Onal, Emily A. Ryan, Luca Scifoni, Thomas M. Orlando, Álvaro Romero‐Calvo, Julie S. Linsey, Meisha L. Shofner   +6 more
wiley   +1 more source

Self-Sustaining Hybrid Passive Cooler Enabling Highly Effective Thermal Management for Outdoor Electronics. [PDF]

Adv Sci (Weinh)
An innovative hybrid passive cooler integrates a porous radiative coating and an atmospheric moisture‐harvesting hydrogel within a melamine sponge skeleton, synergizing radiative cooling, sensible‐heat absorption, and latent‐heat evaporation. It maintains an average 8.3°C sub‐ambient cooling under sunlight and a maximum ∼42.4°C drop under 2000 W·m−2 ...
Du Q, Yang M, Li M, Chen G, Hu Y, Li D, Sun D.   +6 more
europepmc   +2 more sources

Interface Engineering of Porous Transport Layer‐Catalyst Layer in Proton Exchange Membrane Water Electrolyzers: A Comprehensive Review

Advanced Materials Interfaces, EarlyView.
The PTL–CL interface plays a decisive role in PEMWE performance by governing electron conduction, water supply, oxygen removal, catalyst utilization, and interfacial stability. This review summarizes interface‐related resistance sources, characterization methods, and engineering strategies, highlighting rational PTL–CL interface design for low‐cost ...
Aobo Wan, Zhengkai Tu
wiley   +1 more source

Scalable Production of Disordered Nickel‐Iron‐Aluminum Oxides as Stable Anodes for Water Electrolysis: The Role of Aluminum

Advanced Materials Interfaces, EarlyView.
Solution precursor plasma spraying enables the scalable fabrication of porous and disordered nickel‐iron‐aluminum oxide coatings as precious‐metal‐free anodes. Aluminum inhibits crystal growth, optimizes local atomic sites, and enhances charge and ion transport to accelerate reaction kinetics, leading to excellent performance and operational stability.
Tugce Ustunel, Joakim Bäckström, Esdras J. Canto‐Aguilar, Mouna Rafei, Litty Thomas Manamel, Mahesh Ramakrishnan, Konstantin Klementiev, Nina Grunditz, Erik Zimmerman, Thomas Wågberg, Susanne Holmin, Eduardo Gracia‐Espino   +11 more
wiley   +1 more source

Thermo-Mechanical Analysis of Sprayed Layers Using the Finite Element Method

The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science, 2016
The present paper presents an analysis performed in order to determine the thermo-mechanical behavior at the layer-substrate interface in case of thermal spraying, by using the ANSYS R15.0 software.
Roxana-Alexandra GHEŢA, Bogdan DUMITRU, Gabriel Marius DUMITRU, Mădălina-Elena MILITARU   +3 more
doaj  

Hierarchical Multi‐Material Architectures With Gradient Design for Dynamic‐Range Flexible Tactile Sensing

Advanced Materials Technologies, EarlyView.
Hierarchical multi‐material TPMS lattices are engineered as flexible tactile sensors by combining soft and stiff elastomeric layers with a conformal conductive coating. The bilayer architecture delivers sensitivity at low pressures while maintaining a broad detectable range under large loads, enabling reliable pressure and vibration monitoring for ...
Reza Noroozi, Domenic Quiquero, Yan Yan Shery Huang, HaoTian Harvey Shi   +3 more
wiley   +1 more source

Skin‐Like Tri‐Modal Sensors Based on Soft Piezoelectric and Ionic Composites

Advanced Materials Technologies, EarlyView.
Inspired by the multimodal perception of human skin, a soft, skin‐like tri‐modal sensor is presented. The device incorporates an ionically conductive, piezoelectric, elastic composite as its active layer, enabling independent detection of temperature, static strain, and dynamic strain within a single two‐terminal architecture.
Liren Wang, Peter Zalar, Vishva Bhate, Takeo Furukawa, Hidekazu Kodama, Yijun Liu, Yuanyuan Zhou, Chuang Hou, Siyuan Liu, Naoji Matsuhisa   +9 more
wiley   +1 more source

Research on the Properties of Thermal Sprayed Ni-Cr-Si-Fe-B Coatings

Mokslas: Lietuvos Ateitis, 2012
The article deals with the flame sprayed Ni-Cr-Si-Fe-B coating on aluminum alloy substrates. Before the thermal spraying process, aluminum samples were modified applying chemical, mechanical and thermal processing pre-treatment methods. The main aluminum
Raimonda Lukauskaitė, Donatas Šiurkus, Olegas Černašėjus   +2 more
doaj  

Advanced Manufacturing of Composite‐Based Systems for Energy Applications

Advanced Materials Technologies, EarlyView.
Advanced manufacturing enables the integration of polymers, ceramics, metal oxides, and composites into architected microstructures with tailored transport pathways. By coupling material selection, manufacturing strategy, and structural design, multifunctional energy systems can simultaneously improve electrochemical performance, thermal management ...
Sri Vaishnavi Thummalapalli, Dhanush Patil, Libin Yang, M. Taylor Sobczak, Anshul Kulkarni, Xiao Sun, Arunachalam Ramanathan, Tiantian Li, Ramaraja P. Ramasamy, Jason J. Locklin, Yanyu Chen, Xianqiao Wang, Arunachala Mada Kannan, Kenan Song   +13 more
wiley   +1 more source

High Throughput Aerosol Jet Printing to Operationalize High Aspect Ratio Patterning

Advanced Materials Technologies, EarlyView.
High‐throughput aerosol jet printing poses distinct limiting mechanisms to the printing process. These include rapidly changing ink chemistries, atomization instabilities, and liquid‐phase spreading. The combination of in‐line heating, process monitoring, and traditional optimization procedures enables rapid printing of high‐aspect‐ratio structures ...
Bella I. Guyll, Md Mahdi Ul Ishtiaque, Md Ramjan Ali, Todd A. Kingston, Ethan B. Secor   +4 more
wiley   +1 more source