Results 121 to 130 of about 21,710 (287)
Advanced Materials, EarlyView.Elephant‐skin‐inspired crack networks are programmed in porous diatomaceous earth (DE)‐cement composites using substrate‐guided, stress‐concentration induced fracture. The resulting crack lattices act as capillary conduits that redistribute water, while the porous matrix stores moisture.
Qingya Huang +5 more
wiley +1 more source
Options Schemes the Use of Cocurrent Flows in Flame Spraying Coatings
Механика машин, механизмов и материалов, 2014 The article discusses the creation of flame spraying equipment and technologies that implement the various activation schemes of the co current gas flows.
M.A. Belotserkovsky
doaj
Advanced Materials, EarlyView.The perspective presents an integrated view of neuromorphic technologies, from device physics to real‐time applicability, while highlighting the necessity of full‐stack co‐optimization. By outlining practical hardware‐level strategies to exploit device behavior and mitigate non‐idealities, it shows pathways for building efficient, scalable, and ...
Kapil Bhardwaj +8 more
wiley +1 more source
Leaftronics: Bio‐Fractal Scaffolds From Leaf Venation for Low‐Waste Electronics
Advanced Materials, EarlyView.“Leaftronics” transforms naturally evolved leaf venation into quasi‐fractal scaffolds for sustainable electronics. Polymer‐infiltrated leaf skeletons can be used to fabricate ultra‐smooth, reflow‐ and thin‐film‐compatible decomposable substrates, while making the same lignocellulose networks conducting results in flexible transparent electrodes.
Rakesh Rajendran Nair +3 more
wiley +1 more source
The influence of the base material surface preparation on the properties of thermally sprayed coatings [PDF]
Metalurgija, 2010 Using specimens, a research was conducted to determine the influence of the base material surface preparation for 42CrMo4 on the final coating, prior to actual thermal spraying. During thermal spraying, an Al-Ni-alloy was used as an interlayer before the
V. Marušić +2 more
doaj
Thermodynamics and Mechanics of Thermal Spraying of Steel EN 10060 Substrate with NiCrBSi Alloy after Milling. [PDF]
Materials (Basel), 2020 Valíček J +8 more
europepmc +1 more source
Demands and economic aspects of thermal spraying with suspensions - an overview
, 2022 S.368-372Suspensions used as feedstocks for atmospheric plasma spraying (APS) and high velocity oxy-fuel (HVOF) spraying enable coatings with a wide variety of thicknesses, morphologies, and properties to be produced.
Potthoff, Annegret +3 more
core
Advanced Materials, EarlyView.We address the inherently weak particle adhesion of conventional air filters by coating a dynamically crosslinked adhesive layer that delivers capillarity‐driven strong adhesion and particle absorption mediated by dynamic bond exchange. The resulting enhancement in particle adhesion enables efficient ultrafast (up to 20 m s−1) and omnidirectional ...
Junyong Park +11 more
wiley +1 more source
Application for Thermal Spraying for Rail Vehicles
Článek se zabývá základními typy žárových nástřiků (včetně variant prášků, drátů). U těchto žárových nástřiků jsou definovány způsoby aplikace a využití.
Brodský, Jaroslav
core +1 more source
Mechanical and metallurgical properties of two-layered diamalloy 4010 and 2002 HVOF coating [PDF]
, 2011 Diamalloy 4010, which is iron/molybdenum blend, is resistive to wear and Diamalloy 2002 is resistive to corrosion and wear. However, combination of these powders in layered structure, may offer advantages over the individual powders.
AL-Shehri, Yasser Abdullah
core