Results 41 to 50 of about 16,849 (243)
From Food to Power: Hydrogel Thermoelectrics for Ingestible Electronics
Advanced Functional Materials, EarlyView.We introduce a fully edible thermoelectric–electrochromic platform that harvests heat from food and converts it into a visible color change. N‐type and p‐type hydrogel thermoelectric generators connected in series power anthocyanin‐based electrochromic displays, demonstrating the feasibility of safe, biodegradable, ingestible systems for on‐food ...
Antonia Georgopoulou +3 more
wiley +1 more source
BuildingsMist spraying is an active cooling technology used to alleviate heat stress during hot summers. However, there is limited experimental research on the relationship between ambient thermal parameters and spray cooling efficiency, as well as the transient ...
Pin Wang +4 more
doaj +1 more source
Advanced Functional Materials, EarlyView.ABSTRACT Chitosan, a polysaccharide upcycled from biowaste, has long promised sustainable, biocompatible, and antimicrobial films and devices, an appeal reinforced by its recent regulatory recognition, with several chitosan‐based antibacterial dressings gaining clearance through the Food and Drug Administration's 510(k) pathway.
Jacopo Nicoletti +16 more
wiley +1 more source
Progress in Research on Bonding Interface Between Thermal Spraying Coating and Substrate
Cailiao gongcheng, 2017 In the process of thermal spraying remanufacturing,a heterogenerous bonding interface always exists between the coating and matrix due to the materials reason.And the formation and existence of the bonding interface has a significant influence on the ...
LIU Jian +4 more
doaj +1 more source
Advances in Sustainable and Wearable Textile Based Soft Robotics
Advanced Functional Materials, EarlyView.This Review examines advances in wearable textile‐based soft robotics, focusing on sustainable materials, integrated sensing, and scalable actuation. It discusses manufacturing and system integration across healthcare, assistive robotics, prosthetics, and human–machine interfaces, and highlights key challenges in circular design, including life‐cycle ...
Zahir Abbas +6 more
wiley +1 more source
Reduction Rate of Remanent Stress in Thermal Spraying Depositions by Shot Peening
The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science, 2007 Thermal electric-arc spraying coatings are widely utilized both to get new parts ant to repair the used ones. Just like with the other thermal spraying procedures, the other thermal spraying procedures, the thickness of these coatings is limited by the ...
Leonard TEODORU, Valentin MIHAILESCU
doaj
Advanced Functional Materials, EarlyView.Polarity‐matched Zr–MOFs program Nafion's nanoscale morphology during solution casting. Hydrophilic UiO‐66 preserves hydrated pathways, while hydrophobic UiO‐67 increases the proton hopping sites by densifying ionic clusters. Combining both fillers yields a membrane that delivers 176 mS cm−1 conductivity, reaches 1.46 W cm−2 under 200 kPa, and triples ...
Yonghwi Cho +13 more
wiley +1 more source
A comparative review on cold gas dynamic spraying processes and technologies
Manufacturing Review, 2019 Cold gas dynamic spraying (CGDS) is a relatively new technology of cold spraying techniques that uses converging-diverging (De Laval) nozzle at a supersonic velocity to accelerate different solid powders towards a substrate where it plastically deforms ...
Oyinbo Sunday Temitope, Jen Tien-Chien
doaj +1 more source
Advanced Functional Materials, EarlyView.A gradient‐engineered all‐paper sensor is fabricated by integrating MXene and in situ grown AgNPs within hierarchical cellulose networks. The device breaks the sensitivity–detection range trade‐off through cascaded conductive pathways, enabling ultrahigh pressure sensitivity, humidity–pressure decoupled dual‐mode sensing, and outstanding EMI shielding,
Ao Li +7 more
wiley +1 more source
International Journal of Electrochemical Science, 2015 Arc thermal metal spraying method () provides proven long term protective coating systems using zinc, aluminum and their alloys for steel structure in a marine environment. This paper focused on studying the effect of spraying metal type, and presence or
Hong-Bok Choe +3 more
doaj +1 more source