Results 101 to 110 of about 74,346 (217)

Influence of TiC and TiN Ceramic Reinforcements on the Microstructure, Thermal Expansion Behavior, and Tensile Properties of Invar 36 Manufactured by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
This study examines Invar composites reinforced with titanium carbide (TiC) and titanium nitride (TiN) using laser powder bed fusion (LPBF). It presents the influence of reinforcements on microstructure, tensile properties, and thermal expansion. Results show that TiC effectively strengthens Invar while maintaining low thermal expansion, whereas TiN ...
Ayodeji Nathaniel Oyedeji, Natasha Sacks, Johannes Pötschke, Björn Matthey   +3 more
wiley   +1 more source

Reduction Rate of Remanent Stress in Thermal Spraying Depositions by Shot Peening

The Annals of “Dunarea de Jos” University of Galati. Fascicle IX, Metallurgy and Materials Science, 2007
Thermal electric-arc spraying coatings are widely utilized both to get new parts ant to repair the used ones. Just like with the other thermal spraying procedures, the other thermal spraying procedures, the thickness of these coatings is limited by the ...
Leonard TEODORU, Valentin MIHAILESCU
doaj  

Leveraging Symbolic Artificial Intelligence and Fuzzy Logic for Materials Science: A Review of Methods, Challenges, and Applications to Scarce and Imperfect Experimental Data

Advanced Engineering Materials, EarlyView.
This article explores the transformative potential of symbolic artificial intelligence (AI) in the field of materials science, particularly in leveraging experimental data. The article presents several symbolic AI models and discusses their applications in materials science.
Ahmed Amrani, Mohamed‐Ali Belloum, Laurence Boudet, Valentin Fouillard, Edwin Friedmann, Guillaume Lacharme, Ali Mahmoud, Jean‐Philippe Poli   +7 more
wiley   +1 more source

Rapidly Solidified High‐Strength Invar 36 Prepared by Planar‐Flow Melt Spinning

Advanced Engineering Materials, EarlyView.
The Invar 36 alloy was rapidly solidified using the planar‐flow melt‐spinning technique. Ribbon samples with thicknesses ranging from 20 to 160 mm were produced. As the grain size of the ribbon decreased to sub‐micron levels, the hardness increased by more than 2 times.
Bekir Akgül, Mehmet Kul
wiley   +1 more source

Integral relationships for analytical solutions of hyperbolic models of transfer

Тонкие химические технологии, 2010
A new representation of boundary-value problems for transfer equations of hyperbolic type is suggested: the method of Green's functions was developed.
E. M. Kartashov, T. V. Timchenko
doaj  

Gallium Microalloying in Bi–Sn Solders: Interfacial Phase Formation, Wettability, and Long‐Term Shear Reliability Under Isothermal Aging

Advanced Engineering Materials, EarlyView.
Gallium microalloying redirects interfacial reactions in low‐temperature Bi–Sn solders from Cu–Sn toward Cu–Ga intermetallic formation. The resulting Cu–Ga layer suppresses intermetallic growth during thermal aging, alters fracture pathways, and improves interfacial stability.
Iva Králová, Markéta Klimtová, Mohd Faizul Mohd Sabri, Yew Hoong Wong, Petr Veselý, Martin Plaček, Karel Dušek   +6 more
wiley   +1 more source

Degradation Behaviors of NPB Molecules upon Prolonged Exposure to Various Thermal Stresses under High Vacuum below 10^-4 Pa. [PDF]

ACS Omega, 2020
Shim S, Choi E, Kim H, Yun JY.
europepmc   +1 more source

Feasibility and Limitations of the Advanced Replica Process for Bioactive Glasses

Advanced Engineering Materials, EarlyView.
Periodic 3D‐printed Kelvin‐cell templates enable a controlled advanced replica process for fabricating highly porous glass lattices. Across P45K9, 45S5, and 13–93, material‐dependent differences in coating, burnout, and shrinkage lead to distinct strut morphologies, while comparable final porosities of 83%–88% are retained.
Swantje Funk, Elisabeth Keck, Alberto López‐Grande, Delia S. Brauer, Tobias Fey   +4 more
wiley   +1 more source

High‐Entropy Alloy Interlayers Toward Advanced Joining for High‐Performance Structural Applications: Current Progress and Emerging Challenges

Advanced Engineering Materials, EarlyView.
HEA interlayers offer a versatile route for joining high‐performance structural materials. Their compositional and structural design regulates interfacial reactions, suppresses brittle IMCs, and improves metallurgical bonding. Sandwich interlayers further integrate defect healing with precipitation strengthening, enabling improved strength–ductility ...
Lin Yuan, Jiafen Song, Jinglong Li, Jiangtao Xiong, Tao Yang   +4 more
wiley   +1 more source

A Novel Approach to Estimate the Transition Temperature via Dynamic Nanoindentation

Advanced Engineering Materials, EarlyView.
A new dynamic nanoindentation‐based method was developed that uses the stiffness ratio as an indicator of the elastic–plastic deformation contributions at different temperatures. The approach successfully identified transition temperatures in ferritic steel and distinguished them from continuously ductile austenitic steel.
Stefan Zeiler, Nikolaus Kostwein, Ronald Schnitzer, Christian Mitterer, Verena Maier‐Kiener   +4 more
wiley   +1 more source