Results 61 to 70 of about 5,748 (239)

Steady-state thermodynamic process in multilayered heterogeneous cylinder

Open Physics
The present study formulates and further examines a steady-state heat diffusion process in a generalized multilayered heterogeneous circular composite.
Mubaraki Ali M., Nuruddeen Rahmatullah Ibrahim   +1 more
doaj   +1 more source

Thermodynamic analysis of the change of solid solubility in a binary system processed by mechanical alloying

Journal of Alloys and Compounds, 2009
Abstract Using a non-equilibrium process, it is possible to extend the solid solubility range in metallic systems. Therefore, the main objective of this work was to apply a thermodynamic model to predict the change in the solubility limit of systems with positive enthalpy mixing (Cu–Cr and Fe–Cu) processed by mechanical alloying.
Aguilar, C., Martinez, V., Navea, L., Pavez, O., Santander, M.   +4 more
openaire   +3 more sources

Workflow for Design of Experiments‐Based Modeling of Species Transport and Growth Kinetics in GaN Hydride Vapor Phase Epitaxy

Advanced Engineering Materials, EarlyView.
A novel workflow for investigating hydride vapor phase epitaxy for GaN bulk crystal growth is proposed. It combines Design of experiments (DoE) with physical simulations of mass transport and crystal growth kinetics, serving as an intermediate step between DoE and experiments.
J. Tomkovič, G. Lukin, H. Torkashvand, A. Kerschbaum, M. Müller, S. Besendörfer, J. Heitmann, J. Friedrich   +7 more
wiley   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Precipitation Simulations of the O‐Phase in Ti2AlNb Alloys Processed by Laser Powder Bed Fusion

Advanced Engineering Materials, EarlyView.
Simulated and experimental evolution of the O‐phase volume fraction during postprocessing of a Ti‐21Al‐25Nb (at.%) alloy processed by laser powder bed fusion. With results of sensitivity to input parameters from a thorough and quantified analysis, the interfacial energy matrix/precipitate is the most relevant input parameter for the simulation of the O‐
Silvana Tumminello, Joachim Gussone, Suzana G. Fries, Marcus Rackel, Andreas Stark, Norbert Schell, Jan Haubrich, Guillermo Requena   +7 more
wiley   +1 more source

Microstructure, Thermal Transport, and Dry‐Sliding Tribology of Powder‐Metallurgy Al7075 Composites Reinforced With Sol–Gel‐Derived ZnO–rGO Hybrid Nanoparticles

Advanced Engineering Materials, EarlyView.
Sol–gel‐derived ZnO–rGO hybrid nanoparticles enable Al7075 powder‐metallurgy composites to achieve concurrent gains in hardness and thermal conductivity while markedly lowering friction and wear. The hybrid architecture couples ZnO‐based load support with rGO‐assisted lamellar sliding and heat spreading, revealing a promising route toward lightweight ...
Bunyamin Aksakal, Cevher Kursat Macit, Merve Ayık, Hakan Tutumlu   +3 more
wiley   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Simple thermodynamic model of the extension of solid solution of Cu–Mo alloys processed by mechanical alloying

Materials Chemistry and Physics, 2011
Abstract The objective of this work is proposing a simple thermodynamic model to explain the increase in the solubility limit of the powders of the Cu–Mo systems or other binary systems processed by mechanical alloying. In the regular solution model, the effects of crystalline defects, such as; dislocations and grain boundary produced during milling ...
Aguilar, C., Guzman, D., Rojas, P. A., Ordonez, Stella, Rios, R.   +4 more
openaire   +3 more sources

External and Internal Cracking Caused by Heat Treatment in Laser Powder Bed Fusion‐Fabricated Inconel 738LC Components

Advanced Engineering Materials, EarlyView.
Manufacturing problems such as heat treatment‐induced cracking hinder the widespread application of the laser powder bed fusion (LPBF) process to superalloys. In this study, cracks in the LPBF components of Inconel 738LC superalloy are characterized after heat treatment at various temperature ranges, revealing two distinct cracking behaviors.
Kosuke Kuwabara, Masahiro Kusano, Ayako Ikeda, Toshio Osada, Makoto Watanabe   +4 more
wiley   +1 more source

High‐Temperature Phase Transformation in a V‐9Si‐6.5B Alloy: The Kinetic and Crystallographic Pathway From V5SiB2 to V8SiB4

Advanced Engineering Materials, EarlyView.
In situ synchrotron high‐energy X‐ray diffraction reveals the real‐time high‐temperature phase evolution of a ternary V‐9Si‐6.5B alloy. The study uncovers a kinetically delayed V5SiB2 → V8SiB4 transformation governed by massive structural and chemical barriers.
Zahra Sabeti, Andreas Stark, Roja Rani Korrayi, Florian Pyczak, Georg Hasemann   +4 more
wiley   +1 more source