Results 151 to 160 of about 1,375,815 (243)

Interplay Between Dispersion, Nucleation, and Crystallization in HDPE/Graphene Nanocomposites Processed Under Thermokinetic Conditions

Polymer Engineering &Science, EarlyView.
Thermokinetic processing controls graphene fragmentation and dispersion in HDPE, promoting heterogeneous nucleation and multistep crystallization. The balance between nucleation enhancement and chain mobility restriction governs the final crystalline structure and material performance.
Lucas J. S. Nascimento, Tainá dos S. Guatimosim, Fernanda T. G. Dias, Sandro C. Amico, Otávio Bianchi   +4 more
wiley   +1 more source

Energy-based devices for enhanced transdermal drug delivery in pathological scars: A review. [PDF]

Lasers Med Sci
Zhao Y, Ma J, Li B, Lin H.
europepmc   +1 more source

Sustainable PEG‐Based Shape‐Stabilized Phase Change Materials Using Raw Pine Cone as a Low‐Cost Filler and Graphite for Enhanced Thermal Conductivity

Polymer Engineering &Science, EarlyView.
Preparation of sustainable PEG‐based ssPCMs using a PC‐based low‐cos filler and G as a thermal enhancer. PEG 6000 is incorporated into the PC/G matrix through mixing to obtain the shape‐stabilized PCM for thermal energy storage applications. ABSTRACT This study investigates the development of a novel shape‐stabilized phase change material (ssPCM ...
Amira Akrouti, Abdelwaheb Trigui, Mónica Delgado, Miguel Navarro, Ana Lazaro, Rym Hassani   +5 more
wiley   +1 more source

Effects of Annealing on the Thermomechanical Properties and Crystallization Behavior of FDM‐Printed High‐Temperature PLA and Glass Fiber PLA Composites

Polymer Engineering &Science, EarlyView.
Overview of the study evaluating the impact of post‐print annealing on the microstructural crystallization and thermomechanical properties of FDM‐printed high‐temperature PLA and glass fiber‐reinforced PLA composites. ABSTRACT Polylactic acid (PLA) combines renewable sourcing and reliable printability with limited stiffness retention near its glass ...
Huseyin Erdem Yalkin, Ayse Nur Ozkan
wiley   +1 more source

Microstructural Evolution and Mechanical Properties of Investment-Cast Haynes 282 Nickel-Based Superalloy After Heat Treatment and High-Temperature Thermomechanical Processing. [PDF]

Materials (Basel)
Nowotnik A, Wichowska E, Mrowka-Nowotnik G.   +2 more
europepmc   +1 more source

High‐Order Pressure–Volume Relationship for Simulation of Stretch and Extrusion Blow Molding Processes

Polymer Engineering &Science, EarlyView.
High‐order thermodynamically consistent pressure–volume modeling improves numerical stability and prediction accuracy in stretch and extrusion blow molding simulations. The proposed formulation captures transient pressure evolution and enables reliable thickness prediction with good agreement against experimental measurements.
Z. Benrabah, F. Ilinca, A. Bardetti, S. Bournival   +3 more
wiley   +1 more source

Effect of Extrusion Processing on the Instant Properties and Structural Characteristics of Yellow Waxy Corn Flour. [PDF]

Foods
Guo H, Zhang Z, Cheng Z, Li Q, Li Y.
europepmc   +1 more source

Robust β‐myrcene block copolymer elastomeric vitrimers

Polymer International, EarlyView.
Myrcene‐based vitrimeric elastomers were compared: statistical (poly(styrene‐stat‐myrcene‐stat‐AAEMA)] versus ‘hard–soft’ diblock (poly(styrene)‐block‐poly(myrcene‐co‐AAEMA)). The diblock's ability to anchor the glassy poly(styrene) blocks in a self‐assembled microstructure was effective – leading to four times higher tensile stress and ten times ...
Chong Yang Du, Farhad Asempour, Milan Marić   +2 more
wiley   +1 more source

Selection of 3D-Printing Optimal Parameters via MCDM for Maximizing the Thermomechanical Response of TPU and PEEK. [PDF]

Polymers (Basel)
Crespo-Sánchez J, Fernández D, Solek C, Ayllón J, Del Toro SF, Camacho AM, Rodríguez-Prieto Á.   +6 more
europepmc   +1 more source

Performance improvement of carbon fiber‐reinforced ABS composites by introducing fullerene nanoparticles

Polymer International, EarlyView.
Fullerene particles were incorporated with CF‐reinforced acrylonitrile–butadiene–styrene terpolymer (ABS) matrix at three different compositions by a melt‐compounding process. These insights are crucial for the optimization of conductive hybrid composites for various applications.
Alinda Öyku Akar, Ümit Hakan Yıldız, Seha Tirkeş, Ümit Tayfun, Ferda Hacivelioglu   +4 more
wiley   +1 more source