Results 111 to 120 of about 2,889 (254)

In Situ Curing‐Enabled 3D Printing of Continuous Fiber‐Reinforced Thermosetting Composites

Journal of Polymer Science, EarlyView.
In situ curing‐enabled the 3D printing of continuous fiber/thermoset composites, which were reviewed. Particularly, four types of in situ curing, were discussed, including Radiation‐induced curing, photothermal curing, electrothermal curing, and frontal polymerization. AI‐integrated printing was also analyzed.
Xiaofei Wu, Harrison Hayworth, Shiren Wang   +2 more
wiley   +1 more source

Sorbic Acid-Modified Soybean Oil: A Promising Biobased Molecular Platform for Sustainable Thermosetting Resins. [PDF]

ChemSusChem
Silvano S, Vignali A, Boggioni L, Bertini F.   +3 more
europepmc   +1 more source

Viscoelastic Modeling of Stress Relaxation in Model High‐Performance Covalent Adaptable Networks

Journal of Polymer Science, EarlyView.
Covalent adaptable networks, often referred to as vitrimers, contain a certain fraction of bonds that are able to exchange with other bonds. The ability of this bond exchange to relax stress or result in flow of the material depends on the concentration and specific concentration of these bonds in ways that can be quantified.
Broderick Lewis, Benjamin R. Hafner, Cheol Park, Joseph M. Dennis, Kenneth R. Shull   +4 more
wiley   +1 more source

Thermosetting Resins Based on Poly(Ethylene Glycol Fumarate) and Acrylic Acid: Rheological and Thermal Analysis. [PDF]

Molecules
Burkeyeva G, Kovaleva A, Ibrayeva Z, Havlicek D, Minayeva Y, Omasheva A, Zhakupbekova E, Nurmaganbetova M.   +7 more
europepmc   +1 more source

Curing Behavior and Adhesion Performance of a One‐Component Epoxy Resin Based on a Dual‐Locked Thermal Latent Curing Agent

Journal of Polymer Science, EarlyView.
In this study, curing behavior of epoxy resins using a dual‐locked thermal latent curing agent (DCA) was analyzed using DSC and FT‐NIR. The DCA was successfully dissolved in the bisphenol A type epoxy resin (DGEBA). Furthermore, the prepared one‐component epoxy resin was used as an adhesive and achieved excellent adhesive strength (> 25 MPa).
Yukai Ito, Daisuke Aoki, Koji Arimitsu
wiley   +1 more source

Development of Eco-Friendly Thermosetting Resins From Zein and Diglycidyl Ether of Vanillyl Alcohol. A Step Toward Sustainable Materials. [PDF]

Chemistry
Lotos ED, Dinu R, Mihai M, Simionescu BC, Mija A.   +4 more
europepmc   +1 more source

Comparison of Calorimetry and NMR Relaxometry Measurements of Epoxy Cure Kinetics

Journal of Polymer Science, EarlyView.
Single‐sided NMR monitors epoxy cure in three DGEBA/diamine systems, alongside benchmark DSC measurements. Fitting both datasets to a Kamal‐Malkin kinetic model shows NMR‐derived rate constants typically exceed DSC values, revealing an offset between gelation and chemical conversion.
Olivia Cassara, Kayla Copeman, Sydney Joyce Tate, Jack Ballenger, Tyler Meldrum   +4 more
wiley   +1 more source

Review on Frontal Polymerization Behavior for Thermosetting Resins: Materials, Modeling and Application. [PDF]

Polymers (Basel)
Luo T, Ma Y, Cui X.
europepmc   +1 more source

Porous Organic Polymers: From Molecular Design to Scalable Technologies

Small, EarlyView.
This review introduces porous organic polymers (POPs) for a wide range of applications, including energy storage, gas adsorption, catalysts, adsorbents, biomedical applications, sensors, and other exciting fields, and critically analyzes the synthesis and modification, and how structural topology influences the composites' architecture of POPs, along ...
Hossein Mashhadimoslem, Hadi Shayesteh, Simindokht Zarei‐Shokat, Rokhsareh Bakhtiari, Sheyda Abedi‐Banaei, Zahra Sheikhlouiharzand, Parnia Mohebimanesh, Seyed Mohammad Amin Ojagh, Bahareh Bakhtiari, Ali Maleki, Theo G. M. van de Ven, Sohrab Zendehboudi, Ali Elkamel   +12 more
wiley   +1 more source

Effects of Chemical Composition and Cross-Linking Degree on the Thermo-Mechanical Properties of Bio-Based Thermosetting Resins: A Molecular Dynamics Simulation Study. [PDF]

Polymers (Basel)
Tang Q, Jiang J, Li J, Zhao L, Xi Z.
europepmc   +1 more source