Results 121 to 130 of about 1,078,566 (277)

Effect of partial and complete replacement of wood particles with sugar beet pulp on the physical properties of particleboards

Наукові праці Лісівничої академії наук України
The increase in deforestation limits the availability of wood, raises its cost, and intensifies competition for raw materials, thereby complicating the sustainable development of the wood-based panel industry.
Volodymyr Hamanchuk, Pavlo Bekhta, Tomáš Pipíška, Jozef Ráheľ, Jakub Hofman   +4 more
doaj   +1 more source

ChM. Ts. Dr. Siti Qurratu’ Aini develops Green Shale Swelling Inhibitor for shale swelling in the oil and gas industry [PDF]

PEKAN, 17 July 2025 – Concerns over environmental pollution caused by the use of non-environmentally friendly chemicals in the oil and gas industry became the starting point for the development of an eco-friendly formulation to replace the use of ...
Nur Hartini, Mohd Hatta
core   +2 more sources

Photo‐Switchable Molecular Module Programming PET Biodegradation in Aquatic Environments

Advanced Functional Materials, EarlyView.
We address the plastic durability paradox by integrating an itaconic acid–derived pyrrolidone module into polymer backbones. Sunlight in water triggers Norrish Type I ring‐opening and hydrophilization, enabling rapid biodegradation into nontoxic minerals.
Mohammad Asif Ali, Jixin Zheng, Satoshi Wakai, Jie Liu, Hidetaka Nomaki, Misato Tsukatani, Noriyuki Isobe, Jingcheng Sang, Yuriko Aoki, Hideo Okamura, Daisuke Sasaki, Chiaki Ogino, Yuzo Yamazaki, Takashi Nishikaze, Kenji Takada, Maiko K. Okajima, Tatsuo Kaneko   +16 more
wiley   +1 more source

Influence of dry formed fiberboards density on their thickness swelling and water absorption

Annals of Warsaw University of Life Sciences - SGGW Forestry and Wood Technology, 2018
The aim of the research was to determine the thickness swelling and water absorption of dry formed fiberboards produced in laboratory conditions as a result of interaction with moisture, depending on the density of the panels. In the range of work, in addition to the aforementioned tests, the bending strength and modulus of elasticity in bending of the
Grzegorz Kowaluk, Nitychoruk, Karolina
openaire   +1 more source

Impact of core layer thickness on thickness swelling of particleboard

Sorpcijske lastnosti ivernih plošč so odvisne od velikosti gradnikov, kakor tudi od uporabljenega lepila in ne nazadnje tudi od tehnološkega procesa. Pri izdelavi, predvsem pri natresanju, lahko v sami proizvodnji pride do nihanja v količini natresenega ...
Zore, Igor
core  

Swelling-induced changes in coal microstructure due to supercritical CO2 injection

, 2016
©2016. American Geophysical Union. All Rights Reserved. Enhanced coalbed methane recovery and CO2 geostorage in coal seams are severely limited by permeability decrease caused by CO2 injection and associated coal matrix swelling. Typically, it is assumed
Maxim Lebedev (23287390), Y. Zhang (23371516), Ahmed Barifcani (23307550), Stefan Iglauer (23334529), Mohammad Sarmadivaleh (23289628)   +4 more
core  

Reducing the thickness swelling of wood based panels by applying a nanotechnology compound

, 2020
Subject The potential of improving the thickness swelling of commercial wood based panels by applying a new nanotechnology compound was investigated. The application of the compound SurfaPore™ W, an aqueous wood-water repellent resulted in a significant ...
J Eur, Wood Prod
core  

A Magneto‐Mechanically Activated Nerve Guidance Conduit Promotes Peripheral Nerve Regeneration via TIMP1‐Mediated Membrane Tension Transfer

Advanced Functional Materials, EarlyView.
This study presents a magneto‐mechanical strategy that incorporates FP@MSCs into an aligned PCL/GelMA nerve guidance conduit. Magnetic stimulation increases membrane tension in FP@MSCs, triggering cytoskeletal remodeling, Schwann cell‐like differentiation, and TIMP1 secretion. TIMP1 activates ITGB1/CD63–FAK signaling in NE‐4C cells, increasing membrane
Xinyu Zhu, Yumin Wu, Xiang Gao, Tianlu Wang, Wanting Jia, Xueying Mei, Huanzhong Ji, Zongxi Wu, Yujie Liang, Xiang Li, Kan Li, Jingyuan Li, Guangsen Zheng, Guiqing Liao, Siyong Gao   +14 more
wiley   +1 more source

Effect of Density and Polymer Content on the Hygroscopic Thickness Swelling Rate of Compression Molded Wood Fiber/Polymer Composites [PDF]

, 2007
The effects of polymer content and board density on the hygroscopic thickness swelling rate of compression-molded wood fiber/polymer composites were investigated in this study.
Gardner, Douglas J., Shi, Sheldon Q.
core   +1 more source

Deciphering the Photopolymerization‐Induced Nanostructures and Interface Formation for Submicrometer Additive Manufacturing

Advanced Functional Materials, EarlyView.
This work reveals the UV‐curing‐induced monomer‐rich domain, oligomer‐rich domain, and entangled oligomer domain. The cured submicron films in stressed state induce interlayer nano‐wrinkle structures during the deposition of the second layer. Stress‐free cured films in relaxed state form non‐diffusive, diffusive and semi‐diffusive interlayer ...
Shouzheng Chen, Yufeng Zhai, Jungui Zhou, Lixing Li, Simon Schraad, Guangjiu Pan, Xuehe Jiang, Sarathlal Koyiloth Vayalil, Rolf A. T. M. van Benthem, Julien R. G. Navarro, Johan F. G. A. Jansen, Mats K. G. Johansson, Peter Müller‐Buschbaum, Stephan V. Roth   +13 more
wiley   +1 more source