Results 51 to 60 of about 1,115,656 (293)

Harnessing Fungal Biowelding for Constructing Mycelium‐Engineered Materials

Advanced Engineering Materials, EarlyView.
Mycelium‐bound composites (MBCs) offer low‐carbon alternatives for construction, yet interfacial bonding remains a critical challenge. This review examines fungal biowelding as a biocompatible adhesive, elucidating mycelium‐mediated interfacial mechanisms and their role in material assembly. Strategies to optimize biowelding are discussed, highlighting
Xue Brenda Bai, Xinrui Sarah Niu, Zhao Qin   +2 more
wiley   +1 more source

Air-breathing Mg-Cu/CuO fuel cell

Journal of Engineering and Applied Science
Magnesium fuel cells deliver higher electrical power output than lithium-ion batteries and have the potential to become an economically attractive alternative power source for domestic purposes.
R. Jayakrishnan, Aruna Raj, Akhil M. Anand, P C Harikrishnan, Athira Ayyappan   +4 more
doaj   +1 more source

Mammalian-brain-inspired neuromorphic motion-cognition nerve achieves cross-modal perceptual enhancement

Nature Communications, 2023
Inspired by the multisensory cue integration in macaque’s brain for spatial perception, the authors develop a neuromorphic motion-cognition nerve that achieves cross-modal perceptual enhancement for robotics and wearable applications.
Chengpeng Jiang, Jiaqi Liu, Yao Ni, Shangda Qu, Lu Liu, Yue Li, Lu Yang, Wentao Xu   +7 more
doaj   +1 more source

Nanostructured titanium dioxide thin film for dye-sensitized Solar cell applications [PDF]

, 2009
Nanostructured Titanium Dioxide (TiC^) thin film for Dye-Sensitized Solid State Solar Cell (DSSSC) application has been synthesized using sol-gel method and deposited onto silicon and glass substrates using spin coating technique.
Ahmad, Mohd Khairul
core  

Duplex Stainless Steel Laser‐Surface Textured: Stability in Brine Solution

Advanced Engineering Materials, EarlyView.
Controlled laser‐surface treatment (LST) of duplex DSS2205 steel is performed to increase its stability in brine solution under cyclic electrochemical assays. The superior protection with respect to flat and smooth panels is attributed to the presence of FeCr2O4 as the main protective oxide layer in the LST surface, after corrosion tests. The stability
Mohammad Rezayat, Hamidreza Enshaei, Elaine Armelin, José I. Iribarren, Antonio Mateo, Miguel Morales   +5 more
wiley   +1 more source

Unidirectional Tape‐Based Composites from Hemp and Pineapple Leaf Fiber: Mechanical Performance in Conventional and Bio‐Based Matrices

Advanced Engineering Materials, EarlyView.
The study investigates novel semi‐finished products made of unidirectionally arranged hemp or pineapple leaf fiber‐reinforced composites produced from different matrices. The materials are analyzed in terms of their mechanical and interfacial properties and void content.
Nina Graupner, Raja Bade, Valentin Ackermann, Roja M. Baumann, Corvin Bischoff, Jona F. Ebeling, Oskar Glenz, Marlo Groh, Jonathan Groth, Finja Hiller, Tom Hirschmüller, Felix Menke, Syntcha Ngantchou Lecdou, Mika Ohler, Daniel Rafii Vardiny, Darius Richter, Dario Röper, Henrik Schumacher, Theresa Stein, Benjamin Vorbeck, Elisabeth Wermter, Kay Kölzig, Jörg Müssig   +22 more
wiley   +1 more source

A thin-film magnetoresistive angle detector [PDF]

, 1990
An overview is given of the results of our research on a contactless angle detector based on the anisotropic magnetoresistance effect (AMR effect) in a permalloy thin film.
Eijkel, Kees J.M., Fluitman, Jan H.J, Groot, Peter, Leeuwis, Henk, Popma, Theo J.A., Wieberdink, Johan W.   +5 more
core   +2 more sources

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

Utilizing tertiary butyl iodide as an effective film quality enhancing agent for atomic layer deposition of HfO2 dielectric thin films

AIP Advances, 2021
The effects of the initial pulse of tert-butyl iodide as a surfactant in atomic layer deposition of HfO2 using cyclopentadienyl tris(dimethylamino) hafnium, CpHf(NMe2)3, and ozone, O3, are investigated at 320, 300, and 250 °C.
Kok Chew Tan, Jaesun Jung, Sojung Kim, Jongmoon Kim, Seok Jong Lee, Young-Soo Park   +5 more
doaj   +1 more source

Sputter deposition of porous thin films from metal/NaCl powder targets [PDF]

, 2019
A method to deposit porous thin films is elucidated. For this purpose, NaCl powder was mixed with a metal powder, cold pressed, and used as a target material in order to deposit a metal/NaCl thin film by DC magnetron sputtering.
Dedoncker, Robin, Depla, Diederik, Rijckaert, Hannes   +2 more
core   +1 more source