Results 81 to 90 of about 13,057 (231)

Improving the Power Electronics Laboratory teaching/learning process: an interactive web tool [PDF]

open access: yes, 2017
European Higher Education Area; Power Electronics Laboratory; educational methods Resumen: The forthcoming European Higher Education Area implies an important change in the teaching/learning process: it is necessary to get students more involved as well
Blazquez-Parra, Elidia Beatriz   +2 more
core  

Design, Modelling and Control of a MW‐level Hydrogen Converter for an Off‐Grid DC Hydrogen Production System

open access: yesIET Power Electronics, Volume 19, Issue 1, January/December 2026.
This paper proposes a high‐power hydrogen converter specifically designed for megawatt‐level (MW‐scale) off‐grid hydrogen production systems powered by renewable energy sources. A two‐stage ISOP architecture is adopted to fulfill the demanding requirements of high voltage step‐up, high efficiency, low output ripple, and reliable power regulation.
Rui Zhou   +4 more
wiley   +1 more source

Large Signal Model of a Four-quadrant AC to DC Converter for Accelerator Magnets [PDF]

open access: yes, 2001
This paper presents the large signal model of a four-quadrant AC to DC converter, which is expected to be used in the area of particle accelerators. The system’s first stage is composed of a three-phase boost PWM (Pulse Width Modulated) rectifier ...
De la Calle, R   +3 more
core  

Trends in active power line conditioners [PDF]

open access: yes, 1994
Active power line conditioners, which are classified into shunt and series ones, have been studied with the focus on their practical installation in industrial power systems.
Akagi, Hirofumi
core   +1 more source

PWM Dead Times in Automotive Traction Inverters using IGBT, SiC MOSFET, or Si/SiC Fusion Switch Power Modules

open access: yesIET Power Electronics, Volume 19, Issue 1, January/December 2026.
This article features a comprehensive methodology for analyzing and optimizing PWM dead time in automotive traction inverters, applicable to a wide range of power devices, including Si IGBT/Diodes, SiC MOSFETs, and Si/SiC Fusion switches. The proposed methodology enables a systematic comparison of dead time characteristics, focusing on part‐to‐part ...
Tomas Reiter   +4 more
wiley   +1 more source

Power conversion for a novel AC/DC aircraft electrical distribution system [PDF]

open access: yes, 2014
This paper proposes a novel and compact AC/DC electrical distribution system for new generation aircraft. In these new aircraft power systems, all loads are fed by two dc bus systems: at 28V and at +/-270V.
Clare, Jon C.   +3 more
core   +3 more sources

Optimal Placement of Solar PV Using Time‐Series Load Flow Analysis and Diurnal Load Factor in High‐Voltage Distribution Network

open access: yesInternational Transactions on Electrical Energy Systems, Volume 2026, Issue 1, 2026.
In the midst of rapid growth in the power sector, there is a pressing need to address increasing load demands and the introduction of additional electrical vehicle‐related loads. Renewable energy resources, particularly solar photovoltaics (PVs), emerge as crucial allies in meeting the rising electricity requirements. However, integrating solar PV into
Muthuveerappan S.   +3 more
wiley   +1 more source

Research on Electric Vehicle’s Charger Based on PWM Rectifier

open access: yesKongzhi Yu Xinxi Jishu, 2012
A charging-discharging device of electric vehicle’s battery is designed based on main circuit topology of three-phase voltage source PWM rectifier.
LUO Yunfei
doaj  

Input current shaped ac-to-dc converters [PDF]

open access: yes
Input current shaping techniques for ac-to-dc converters were investigated. Input frequencies much higher than normal, up to 20 kHz were emphasized. Several methods of shaping the input current waveform in ac-to-dc converters were reviewed.

core   +1 more source

Battery powered high efficiency drive systems in practical applications [PDF]

open access: yes, 2015
Since about 30 years three-phase variable speed drives are the standard industrial solution when high reliability, high ingress protection of machine and especially high efficiency are required.
Weiss, H.
core  

Home - About - Disclaimer - Privacy