Results 1 to 10 of about 137,033 (118)

Three-point bending performances of integral-forming aluminum foam sandwich

Materials & Design, 2023
In the course of service, integral-forming aluminum foam sandwich (IFAFS) needed to bear three-point bending loads in different directions, however, its deformation mechanism and failure modes were still unclear.
Zichen Zhang, Zan Zhang, Nannan Liu, Xingchuan Xia, Zeng Wang, Jiacheng Wang, Lipeng Cui, Zixuan Qiu, Jian Ding, Yujiang Wang, Yongchang Liu   +10 more
doaj   +3 more sources

Experimental and Numerical Investigation of Reinforcement Sheet Effect on the Bending Strength of Corrugated Composite Panels [PDF]

Mechanics of Advanced Composite Structures, 2021
This paper investigates the influence of reinforcement sheet on the bending strength of corrugated composite panel by numerical and experimental analysis based on three-point bending tests in both longitudinal and transverse directions.
Ali Hemmatian Soorki, Abdulreza Kabiri Ataabadi, Mohsen Loh-Mousavi   +2 more
doaj   +1 more source

Fracture properties of rubber concrete under three-point bending

Shuili Shuiyun Gongcheng Xuebao, 2021
Through the rubber concrete three-point bending beam fracture test, the load, deflection and crack opening displacement values of the rubber concrete are measured, and the load-deflection curve and the load-crack opening displacement curve are drawn ...
LIU Miaoyan, LU Jun, MING Pan
doaj   +1 more source

Fractal Dimension Analysis of Three-Point Bending Concrete Test Specimens [PDF]

MATEC Web of Conferences, 2020
The paper deals with the analysis of the fractal dimension of fracture surfaces of concrete specimens tested in a three-point bending configuration.
Sobek Jakub, Frantík Petr, Trčka Tomáš, Lehký David   +3 more
doaj   +1 more source

Bending Failure Behavior of the Glass Fiber Reinforced Composite I-Beams Formed by a Novel Bending Pultrusion Processing Technique

AUTEX Research Journal, 2022
The glass fiber reinforced resin matrix composite I-beams were designed and formed via a type of novel bending pultrusion processing technique, and the three-point bending tests were carried out to analyze the mechanical bending performances.
Zhu Lvtao, Cao Shengbin, Zhang Xiaofeng, Li Lei   +3 more
doaj   +1 more source

Bending-damaged fracture criterion and numerical implementation of limestone beam under three-point bending test

Frontiers in Earth Science, 2023
To study the characteristics of tensile cracking by rock-bending damage, the bending stress–strain curves and the cumulative ringing counts were obtained by a three-point bending test and acoustic emission (AE) monitoring of limestone beams. Based on the
Benyun Li, Yunlei Tian, Jiao Tian, Shuangying Zuo, Shuangying Zuo, Shiwan Chen, Shiwan Chen   +6 more
doaj   +1 more source

Effect of layer number on bending behavior of 3D spacer composite plates produced with different methods

Firat University Journal of Experimental and Computational Engineering, 2022
In this study, the three-point bending behavior of laminated composite plates reinforced with three-dimensional (3D) spacer fabric was experimentally investigated.
Mustafa Gür, Mete Onur Kaman, Serkan Erdem   +2 more
doaj   +1 more source

Some features of flat fiberglass specimens’ behavior under three-point bending [PDF]

E3S Web of Conferences, 2023
The authors carried out the experimental works devoted to the problem of describing the processes occurring under long-term loading of composite materials.
Kayumov R. A., Strakhov D. E.
doaj   +1 more source

Effect of span-thickness ratio on bending properties of high-strength glass fiber reinforced composite unidirectional plate

Journal of Aeronautical Materials, 2022
Based on the three-point bending test, the bending performances of S6C10-800/AC318 composite unidirectional plates with different span-thickness ratios (hereinafter referred to as unidirectional plates) were tested, and the effect of span-thickness ratio
BAI Xin, WANG Yunying, WANG Yana, CHEN Xinwen, HE Yuhuai   +4 more
doaj   +1 more source

Flexural behavior of composite material under three point bending load [PDF]

E3S Web of Conferences
The behavior of composite materials under tensile and bending loading differs, and material designs optimized for tensile loading may not be suitable for applications subjected to bending loading.
Gupta Manish, Gundlapalle Rajesh, Annapoorna E., Al-Farouni Mohammed, Tyagi Lalit Kumar, Pratap Bhishm   +5 more
doaj   +1 more source