Results 171 to 180 of about 435,500 (212)
Some of the next articles are maybe not open access.
Materials Science and Engineering, 1987
Abstract Planar impact experiments were performed on Ti6Al4V specimens (where the composition is in approximate weight per cent) subjected to different heat treatmetns in order to determine their spall strengths and fracture mechanisms. The technique used was based on recording the spall signal with an embedded manganin stress gauge.
Y. Me-Bar, M. Boas, Z. Rosenberg
openaire +1 more source
Abstract Planar impact experiments were performed on Ti6Al4V specimens (where the composition is in approximate weight per cent) subjected to different heat treatmetns in order to determine their spall strengths and fracture mechanisms. The technique used was based on recording the spall signal with an embedded manganin stress gauge.
Y. Me-Bar, M. Boas, Z. Rosenberg
openaire +1 more source
Alloy Digest, 2002
Abstract Carpenter titanium alloy 6Al-4V is an alpha-beta alloy that contains alpha and beta stabilizers and can be heat treated. This alloy accounts for more than 50% of total titanium usage, mostly in aerospace applications. This datasheet provides information on composition, physical properties, elasticity, tensile properties, and ...
openaire +1 more source
Abstract Carpenter titanium alloy 6Al-4V is an alpha-beta alloy that contains alpha and beta stabilizers and can be heat treated. This alloy accounts for more than 50% of total titanium usage, mostly in aerospace applications. This datasheet provides information on composition, physical properties, elasticity, tensile properties, and ...
openaire +1 more source
Alloy Digest, 2002
Abstract Carpenter titanium alloy Ti 6Al-4V ELI is a high-purity (extra-low-interstitial) version of Ti 6Al-4V (see Alloy Digest Ti-60, August 2002). The alloy is alpha plus beta and has good biocompatibility. This datasheet provides information on composition, physical properties, elasticity, tensile properties, and compressive, shear ...
openaire +1 more source
Abstract Carpenter titanium alloy Ti 6Al-4V ELI is a high-purity (extra-low-interstitial) version of Ti 6Al-4V (see Alloy Digest Ti-60, August 2002). The alloy is alpha plus beta and has good biocompatibility. This datasheet provides information on composition, physical properties, elasticity, tensile properties, and compressive, shear ...
openaire +1 more source
Diffusion Bonding of Ti-6Al-4V Sheet with Ti-6Al-4V Foam for Biomedical Implant Applications
Metallurgical and Materials Transactions B, 2013Advanced metallic bone implants are designed to have a porous surface to improve osseointegration and reduce risks of loosening. An alternative approach to existing surface treatments to create a porous surface is to bond separately produced metallic foams onto the implant.
Brittany Hamilton +3 more
openaire +1 more source
Materials Science and Engineering: A, 1997
Abstract Gas-pressure bulge forming of unreinforced Ti-6Al-4V and TiC-reinforced Ti-6Al-4V was performed while cycling the temperature around the allotropic transformation range of the alloy (880–1020 °C). The resulting domes exhibited very large strains to fracture without cavitation, demonstrating for the first time the use of transformation ...
D.C. Dunand, S. Myojin
openaire +1 more source
Abstract Gas-pressure bulge forming of unreinforced Ti-6Al-4V and TiC-reinforced Ti-6Al-4V was performed while cycling the temperature around the allotropic transformation range of the alloy (880–1020 °C). The resulting domes exhibited very large strains to fracture without cavitation, demonstrating for the first time the use of transformation ...
D.C. Dunand, S. Myojin
openaire +1 more source
Evaluation of residual stresses induced by cold spraying of Ti-6Al-4V on Ti-6Al-4V substrates
Surface and Coatings Technology, 2019Abstract Cold spray (CS) is a solid-state additive material deposition technique, which has gained attention in the aerospace industry as a potentially viable technology for structural repair of high-value parts made of high-strength alloys such as Ti-6Al-4V (Ti-64).
Dibakor Boruah +7 more
openaire +1 more source
MRS Proceedings, 1983
ABSTRACTTitanium and many of its alloys show very poor wear resistance considering their hardness. This together with high thermodynamic driving forces to form very hard compounds between titanium and nitrogen or carbon made titanium based alloys obvious candidates for ion implantation.
W. C. Oliver +4 more
openaire +1 more source
ABSTRACTTitanium and many of its alloys show very poor wear resistance considering their hardness. This together with high thermodynamic driving forces to form very hard compounds between titanium and nitrogen or carbon made titanium based alloys obvious candidates for ion implantation.
W. C. Oliver +4 more
openaire +1 more source
Spallation in the Alloy Ti-6Al-4V
AIP Conference Proceedings, 2002The dynamic tensile (spall) strength of the common engineering titanium alloy Ti‐6Al‐4V has been investigated as a function of impact stress and specimen thickness under conditions of symmetrical impact. Flyer and target plate geometries have been controlled such that release fans from the rear of the flyer and the target meet in the middle of the ...
Bourne, Neil, Church, P D, Andrews, T
openaire +3 more sources
2020
The 2???3-layer structures, consisting of Ti???6Al???4V alloy and composites on its base with 5...10 % particles of ??i?? or ??i??, were produced by the method of cold pressing and vacuum sintering of multi-component powder mixtures on the base of hydrogenized titanium powder.
openaire +3 more sources
The 2???3-layer structures, consisting of Ti???6Al???4V alloy and composites on its base with 5...10 % particles of ??i?? or ??i??, were produced by the method of cold pressing and vacuum sintering of multi-component powder mixtures on the base of hydrogenized titanium powder.
openaire +3 more sources
Deformation characteristics of Ti–6Al–4V
Materials Science and Technology, 1988AbstractThe deformation characteristics of Ti–6Al–4V have been established by torsion testing in the temperature range 800–1150°C. Constitutive equations are proposed for both the β-region and the α+β-region which, it is suggested, may have some practical applications.
T. Sheppard, J. Norley
openaire +1 more source