Results 171 to 180 of about 264,740 (325)

Enhanced Oxidation and Thermal Shock Resistance of N‐type Mg2Si0.89(Sn0.1,Sb0.01) Thermoelectric Material via Cr0.9Si0.1 Coating

open access: yesAdvanced Engineering Materials, EarlyView.
Cr0.9Si0.1 protective coatings are developed to enhance the thermal‐shock and oxidation resistance of Mg2Si0.89(Sn0.1,Sb0.01) thermoelectric (TE) materials. The coating forms a dense and adherent barrier that suppresses oxygen diffusion and mitigates mechanical degradation during cyclic oxidation, demonstrating its potential to improve the long‐term ...
Mikdat Gurtaran   +3 more
wiley   +1 more source

Microstructural Evolution and Mechanical Performance of Plasma‐Assisted Hybrid Friction Stir Welded Dissimilar Aluminum–Copper Joints

open access: yesAdvanced Engineering Materials, EarlyView.
Plasma‐assisted hybrid friction stir welding of dissimilar AlCu joints employs localized plasma preheating to balance heat input and enhance plastic flow. The optimized process reduces axial force by up to 35%, refines the microstructure, and achieves ≈96% joint efficiency.
Deepak Kumar Yaduwanshi   +3 more
wiley   +1 more source

Hardware-in-the-Loop Testing of Spacecraft Relative Dynamics and Tethered Satellite System on a Tip-Tilt Flat-Table Facility [PDF]

open access: gold
Giuseppe Governale   +8 more
openalex   +1 more source

Rheocasting versus Die Casting: An Insight into the Low‐Cycle Fatigue Behavior of AlSi7Mg0.6

open access: yesAdvanced Engineering Materials, EarlyView.
The study compares rheocast lightweight components with high‐pressure die cast materials regarding microstructure and fatigue behavior. Rheocast process offers higher efficiency due to lower casting temperatures. Despite some microstructural differences, both processes show similar strengths (yield strength 125 MPa, tensile strength 240 MPa).
Julia Richter   +4 more
wiley   +1 more source

Can Ti‐Based MXenes Serve as Solid Lubricants for Brake Applications? A Tribological Study

open access: yesAdvanced Engineering Materials, EarlyView.
This study explores the first implementation of Ti‐based MXenes materials in brake pad friction composite material. The resulting composite material exhibits a 48% reduction in the wear rate; alongside significant improvements are observed for thermal and mechanical properties.
Eslam Mahmoud   +7 more
wiley   +1 more source

Interaction between Molten Al‐Killed Mn–B Steel and Carbon‐Bonded MgO Refractories Based on Recyclates

open access: yesAdvanced Engineering Materials, EarlyView.
High‐temperature interactions between low‐sulfur Al‐killed Mn–B steel and MgO–C refractories (0 and 50 wt% recyclates) are studied via finger immersion tests (1600 °C). Surface‐active elements influence infiltration. MgO/CaS layer forms, along with spinel and calcium silicate.
Matheus Roberto Bellé   +5 more
wiley   +1 more source

Screen‐Printed Flexible Piezoelectric Force Sensor Array with Electromagnetic Interference Shielding

open access: yesAdvanced Engineering Materials, EarlyView.
This article introduces a flexible screen‐printed piezoelectric sensor array designed for low‐frequency healthcare applications such as tactile sensing and cardiovascular monitoring. The device integrates interface electronics enabling the simultaneous acquisition of up to 128 signals, along with flexible EMI shielding that significantly reduces noise ...
Joseph Faudou   +6 more
wiley   +1 more source

PR Interval as a Valuable Predictor of Tilt Table Test Results in Patients With Neurally Mediated Syncope. [PDF]

open access: yesAnn Noninvasive Electrocardiol
Nikoo MH   +9 more
europepmc   +1 more source

Home - About - Disclaimer - Privacy