Results 121 to 130 of about 258,109 (284)

Enhancing Corrosion Resistance and Mechanical Strength of 3D‐Printed Iron Polylactic Acid for Marine Applications via Laser Surface Texturing

Advanced Engineering Materials, EarlyView.
Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat, Mojtaba Karamimoghadam, Mohammadreza Lalegani Dezaki, Ali Zolfagharian, Giuseppe Casalino, Antonio Mateo, Mahdi Bodaghi   +6 more
wiley   +1 more source

Dynamic Precipitation during High‐Pressure Torsion of a Magnesium–Manganese Alloy

Advanced Engineering Materials, EarlyView.
An ultrafine‐grained alloy is produced by high‐pressure torsion of solutionized Mg–1.35 wt% Mn. Precipitation of nanometer‐scale Mn particles during deformation provides pinning sites. This prevents the formation of a bimodal grain structure and results in a finer grain size than for pure Mg.
Julian M. Rosalie, Anton Hohenwarter
wiley   +1 more source

Understanding the Effect of Resistance Temperature Detector Temperature Controllers on Microstructural Alignment in Magnetic Freeze Casting

Advanced Engineering Materials, EarlyView.
The effect of temperature controllers that are commonly used in freeze‐casting is investigated in this work. Temperature controllers are observed to generate a voltage in the slurry. Microstructural alignment and ultimate compressive strength data show this voltage to interfere with the ability to align the microstructure using magnetic fields ...
Maddie A. Schmitz, Steven E. Naleway
wiley   +1 more source

Optimization of the Tilt Angle of Solar Panels for Seven Cities in Türkiye

Turkish Journal of Electrical Power and Energy Systems
Türkiye occupies a crucial position in harnessing solar energy due to its solar radiation and duration of exposure to the sun. To maximize energy yield from solar power, photovoltaic panels must be inclined at an optimum angle relative to the sun’s ...
Ayse Inan, Afrah A. J. Qali , Hidir Duzkaya, M. Cengiz Taplamacioglu   +3 more
doaj   +1 more source

Composite Electrospun Fibers Containing Optimized B‐ and Cu‐Doped Bioactive Glass Sol‐Gel Particles for Potential Soft Tissue Engineering Applications

Advanced Engineering Materials, EarlyView.
This article describes the preparation and characterization of poly(ε‐caprolactone) electrospun composite fibers incorporating sol‐gel‐derived bioactive glass particles doped with B and Cu. Scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, Fourier‐transform infrared spectroscopy, contact angle, acellular bioactivity, mechanical and ...
Elisa Piatti, Marta Miola, Liliana Liverani, Paolo Sartori, Enrica Verné, Aldo R. Boccaccini   +5 more
wiley   +1 more source

Tilt aftereffect with small adapting angles [PDF]

Perception & Psychophysics, 1981
B C, Skottun, T, Johnsen, S, Magnussen
openaire   +2 more sources

Evaluation of the Potential of Laser Shock Peening Compared with Cold Expansion for Improving Fatigue Resistance of Riveted Lap Joints of Aerospace Grade 7175 Al Alloy

Advanced Engineering Materials, EarlyView.
This study investigates laser shock peening for enhancing fatigue performance of riveted aerospace aluminum joints. A comparative approach with cold expansion combines fatigue testing and synchrotron X‐ray methods. Integrating mechanical testing with residual stress and strain characterization provides insights into how different treatments affect the ...
Ogün Baris Tapar, David Osman Busse, Maximilian Sprengel, Domenico Furfari, Marc‐André Nielsen, Guilherme Abreu Faria, Jérémy Epp   +6 more
wiley   +1 more source

Adjustment of Coatings Morphology and Particle Distribution of Layered Silicates by Freeze‐Drying for Improved Gas Barriers

Advanced Engineering Materials, EarlyView.
Freeze‐drying of layered silicate is the key to get coatings with superior gas barrier. Freeze‐drying of layered silicates modified with dodecylamine (DDA) is a highly effective technique for the preparation of barrier pigments that significantly mitigate the permeation of oxygen, water vapor, and hydrogen through polymer films containing these ...
Joshua Lommes, Moritz Bätcher, Andrea Deißenberger, Volkmar Stenzel, Andreas Hartwig   +4 more
wiley   +1 more source

Is Young's Modulus a Critical Coating Property Determining Fouling‐Release Performance of Marine Coatings?

Advanced Engineering Materials, EarlyView.
The release of foulers from protective marine coatings is determined by several interrelated material properties, including the strength of Young's modulus, the flexibility of chain segments, the surface free energy, and the magnitude of hydrodynamic stress.
Johann C. Schaal, Andreas Brinkmann, Andreas Hartwig   +2 more
wiley   +1 more source

The Effect of 3D Printing Tilt Angle on the Penetration of 3D-Printed Microneedle Arrays. [PDF]

Micromachines (Basel), 2023
Razzaghi M, Akbari M.
europepmc   +1 more source