Results 151 to 160 of about 72,432 (302)

Effects of Partial-Contact Tool Tilt Angle on Friction Stir Welded AA1050 Aluminum Joint Properties. [PDF]

Materials (Basel), 2023
Abdullah ME, M Rohim MN, Mohammed MM, Derazkola HA.   +3 more
europepmc   +1 more source

Simultaneous surface texture classification and illumination tilt angle prediction

, 2008
In this paper we investigate the effect of the illuminant tilt rotation over surface textures by analysing a set of image texture features extracted from the co-occurrence matrix.
J. Martí, X. Lladó, M. Petrou, A. Oliver, J. Freixenet   +4 more
core  

On the Lightweight Potential of Laser Additive Manufactured NiTi Triply Periodic Minimal Sheet Lattices

Advanced Engineering Materials, EarlyView.
This study explores the lightweight potential of laser additive‐manufactured NiTi triply periodic minimal surface sheet lattices. It systematically investigates the effects of relative density and unit cell size on surface quality, deformation recovery, compression behavior, and energy absorption.
Haoming Mo, Shuo Qu, Shiming Gao, Xu Song   +3 more
wiley   +1 more source

Comparison of Different Head Tilt Angles in Tomotherapy and Volumetric Modulated Arc Therapy for Hippocampal-Avoidance Whole-Brain Radiotherapy

Technology in Cancer Research & Treatment
Purpose Hippocampal-avoidance whole-brain radiotherapy (HA-WBRT) planning can present challenges. This study examines the influence of head tilt angles on the dosimetric characteristics of target and organs at risk (OARs), aiming to identify the optimal ...
Yang Li MS, Cuiyun Yuan MS, Dongjie Chen MD, Sisi Xu MD, Wei Jiang MD, Jiaxin Huang BS, Shanshan Ye BS, Yin Zhang MS, Jun Liang MD, Chenbin Liu PhD   +9 more
doaj   +1 more source

The larger patellar tilt angle and lower intercondylar notch angle might increase posterior cruciate ligament injury risk: a retrospective comparative study. [PDF]

BMC Musculoskelet Disord, 2023
Huo Z, Hao K, Fan C, Li K, Li M, Wang F, Niu Y.   +6 more
europepmc   +1 more source

Electrochemical Evaluation of Compressed Selective Laser Melted AlSi7Mg and AlSi10Mg Alloys in Chloride Environment

Advanced Engineering Materials, EarlyView.
The corrosion performance of AlSi7Mg and AlSi10Mg alloys produced through selective laser melting (SLM) was examined under compressive stress in a chloride environment. Electrochemical analyses, including open‐circuit potential (OCP), potentiodynamic polarization (CPP), and electrochemical impedance spectroscopy (EIS), were complemented by scanning ...
Femi John Akinfolarin, Samson Dare Oguntuyi, Peter Apata Olubambi   +2 more
wiley   +1 more source

Introduction of a New Radiographic Parameter to Predict Proximal Junctional Kyphosis in Adult Spinal Deformity: UIVPTA (Uppermost Instrumented Vertebra-Pelvic Tilt Angle). [PDF]

Neurospine, 2023
Park SJ, Lee CS, Park JS, Shin TS.
europepmc   +1 more source

A Workflow to Accelerate Microstructure‐Sensitive Fatigue Life Predictions

Advanced Engineering Materials, EarlyView.
This study introduces a workflow to accelerate predictions of microstructure‐sensitive fatigue life. Results from frameworks with varying levels of simplification are benchmarked against published reference results. The analysis reveals a trade‐off between accuracy and model complexity, offering researchers a practical guide for selecting the optimal ...
Luca Loiodice, Krzysztof S. Stopka, Michael D. Sangid   +2 more
wiley   +1 more source

Evaluation of lateral and anterior center-edge angles according to sex and anterior pelvic plane tilt angle: a three-dimensional quantitative analysis. [PDF]

J Orthop Surg Res, 2023
Hong KB, Lee WS, Kang K, Kang KT, Cho BW.   +4 more
europepmc   +1 more source

Prediction of Surface Topography Parameters in Direct Laser Interference Patterning of Stainless Steel Using Infrared Monitoring and Convolutional Neural Networks

Advanced Engineering Materials, EarlyView.
This study presents an infrared monitoring approach for direct laser interference patterning (DLIP) combined with a convolutional neural network (CNN). Thermal emission data captured during structuring are used to predict surface topography parameters.
Lukas Olawsky, Marcelo Sallese, Leander Kläber, Clemens Kuhn, Keming Du, Andrés Fabián Lasagni   +5 more
wiley   +1 more source