Results 131 to 140 of about 72,876 (262)
Soft Mechanical‐Electrical Logic Using Liquid Metal‐Filled 3D‐Printed Architectures
Advanced Engineering Materials, EarlyView.We present 3D‐printed soft mechanical–electrical logic elements that use liquid metal–filled silicone tubes actuated by thermoplastic polyurethane/polylactic acid (TPU/PLA) architectures to produce Boolean operations. Complementary normally open and normally closed unit cells perform repeatable binary transitions and can be combined into more complex ...
Christoph Lehmann +2 more
wiley +1 more source
Blade Tip Timing Technique: Theoretical Principles and Simulation of an Experimental Test
, 2015 The Blade Tip Timing (BTT) is a technique that measures the vibration amplitude and frequency of the blades of bladed disks by using a set of probes. The objective of the thesis is to compare the accuracy of the different methods proposed in literature ...
Giovanni Rigosi (7985789)
core
Sparse Representation Based Frequency Detection and Uncertainty Reduction in Blade Tip Timing Measurement for Multi-Mode Blade Vibration Monitoring. [PDF]
Sensors (Basel), 2017 Pan M, Yang Y, Guan F, Hu H, Xu H.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Graphene nanoplatelet (0.1 wt.%) reinforcement significantly enhances the performance of β Ti‐28Nb‐35.4Zr alloy. Grain refinement, reduced water contact angle, and improved surface characteristics promote osteoblast adhesion and complete surface coverage after 7 days.
Khurram Munir +5 more
wiley +1 more source
Secondary rhinoplasty in the cleft lip patient
B-ENT, 2006 Secondary rhinoplasty in the cleft lip patient. Secondary surgery of the cleft lip nose is very complex due to its specific pathological anatomical characteristics.
G. J. Nolst Trenité
doaj
In Situ Micromechanical Study of Bimodal γ′–γ″ Precipitate Assemblies in Ni–Cr–Al–Nb Superalloy
Advanced Engineering Materials, EarlyView.A Ni–Cr–Al–Nb superalloy with a bimodal γ′–γ″ precipitate distribution is developed. Composite precipitate assemblies form through heterogeneous nucleation, effectively impeding dislocation motion. Micropillar compression reveals high strength at room and elevated temperatures, governed by precipitate shearing, with coupled faulting mechanisms ...
Ujjval Bansal +4 more
wiley +1 more source
A non-uniformly under-sampled blade tip-timing signal reconstruction method for blade vibration monitoring. [PDF]
Sensors (Basel), 2015 Hu Z, Lin J, Chen ZS, Yang YM, Li XJ.
europepmc +1 more source
Advanced Engineering Materials, EarlyView.Aluminum and nitride coatings are used in industry because they are hard, resist wear, and protect against oxidation. Adding boron can improve friction behavior and other properties. This study tests coatings on surfaces with different finishes. Results show smoother surfaces perform better, while rough ones wear faster, although coatings can reduce ...
Adrián Claver +9 more
wiley +1 more source
Influence of Geometric Design on Mechanical Performance of Auxetic Metastructure
Advanced Engineering Materials, EarlyView.Strategic geometric reinforcement transforms auxetic performance. This study evaluates 3D‐printed arrowhead metastructures, revealing that a modified design with local ring reinforcement suppresses premature failure to achieve superior energy absorption and structural efficiency.
Muhammad Gulzari +3 more
wiley +1 more source
A Dislocation Perspective on Strength and Toughness in Ceramics
Advanced Engineering Materials, EarlyView.Dislocations in ceramics enjoy a long but yet under‐appreciated history. The three research waves for dislocations in ceramics highlight the topic evolution over the last 90 years. This review focuses on the impact of dislocation on strength and toughness in ceramics.
Xufei Fang
wiley +1 more source