Results 91 to 100 of about 56,271 (309)
Floating zone process for drawing small diameter fibers of refractory materials [PDF]
, 1972 New process produces controlled purity, very high strength, single crystal fibers of materials with melting points to 4000 C. Process has been used to make single crystal fibers of highly refractory ceramics such as aluminum oxide, titanium carbide and ...
Haggerty, J. +3 more
core +1 more source
Wear maps for TiC composite based coatings deposited on 303 stainless steel [PDF]
, 2014 Dry sliding wear (pin-on-disc) tests were carried out under ambient conditions at room temperature for TiC coated and uncoated 303 stainless steel, using alumina as a counterface.
Rasool, G., Stack, M.M.
core +1 more source
Ion‐Confinement‐Assisted Erasure Purifies Oxidized MXene for Reuse
Advanced Science, EarlyView.An erasure‐purification strategy removes surface‐derived TiO2 from oxidized Ti3C2Tx MXene by ion‐confinement‐induced interfacial conversion to soluble titanates, followed by brief acid washing. The scalable process enables approximately 70% material recovery, restores electrical conductivity, and recovers functional performance, including high ...
Xuefeng Zhang +11 more
wiley +1 more source
Česká Stomatologie a Praktické Zubní Lékařství, 2009 Adsorption of biopolymers at the titanium and titanium carbide surface increases the optical roughness as well as the thickness and refractive index of the surface layer. Fibrinogen is better adsorbed at the titanium surface which is treated by polishing
S. Bartáková +8 more
doaj
Temperature effects on material characteristics [PDF]
, 1960 Some of the physical properties of the main elements of interest in high temperature technology are reviewed. Some general trends emerge when these properties are viewed as a function of melting point, but there are a few notable exceptions. Titanium,
Kennedy, A. J., Murphy, A. J.
core
Titanium Carbide Coating on Iron
Journal of the Metal Finishing Society of Japan, 1967 The plating conditions of titanium carbide on iron were investigated in the temperature range of 850-1100°C. Hydrocarbon mixed with titanium tetrachloride carried by hydrogen was introduced over a test specimen of cast iron or mild steel. The direct coating on iron resulted in severe corrosion and cementation of the ground metal, which disturbed the ...
Takehiko TAKAHASHI +2 more
openaire +2 more sources
Solution‐Processed Organic Photovoltaics: Fabrication Advances and Challenges
Advanced Science, EarlyView.This review highlights recent advances in organic photovoltaic (OPV) device fabrication, emphasizing how material selection, interface engineering, and scalable processing techniques shape device performance. It discusses progress in photoactive and charge transport layers, electrode optimization, and large‐area manufacturing, offering insights into ...
Kerui Liu +4 more
wiley +1 more source
Synthesis of Titanium Carbide by the Combustion of TiO2-2Mg-C and 3TiO2-4Al-3C Systems in a Tubular Furnace [PDF]
Iranian Journal of Chemistry & Chemical Engineering, 2009 The combustion process of TiO2- 2Mg- C and 3TiO2-4Al-3C systems in a tubular furnace was investigated. TiC has been synthesized by the magnesiothermic reaction from a mixture of compacted powders of TiO2, Mg and charcoal as starting materials in the ...
Hassan Hadadzadeh +2 more
doaj
Functionalization of two-dimensional tungsten diselenide and MXene for tunable optical property [PDF]
, 2020 Since the discover of graphene in 2004, two-dimensional (2D) materials have gained tremendous attention because of their distinctive properties relative to their bulk form.
Wang, Yueyin
core
Molecular recognition on acoustic wave devices [PDF]
, 1992 Microporous thin films composed either of zeolite crystals embedded in sol-gel derived glass or of a molecular coupling layer, zeolite crystals and a porous silica overlayer, were formed on the gold electrodes of Quartz Crystal Microbalances (QCM). The
Bein, Thomas +4 more
core +1 more source