Results 251 to 260 of about 157,979 (290)

Strain Development During Cure of Partially Pre‐Cured Thermosetting Composites Measured With Distributed Fiber Optic Sensors

Polymer Composites, EarlyView.
Schematic representation of the beneficial effect of ply pre‐curing on temperature overshoot, internal strain and warpage during cure of thin and thick thermosetting composites. ABSTRACT Detection of manufacturing‐induced defects in thermosetting composites is crucial to guarantee part quality, safety, and improve manufacturing efficiency.
Francesco Taddei, Giacomo Struzziero, Valentin Ott, Véronique Michaud   +3 more
wiley   +1 more source

Case Report: Glomerular microangiopathy and reversible renal toxicity during prolonged bevacizumab therapy in ovarian cancer. [PDF]

Front Oncol
Kwon J, Choe M, Paek JH, Park WY, Jin K, Han S, Cho CH, Kim Y.   +7 more
europepmc   +1 more source

Cationic‐Hydrophilic Di‐Block Copolymers: Surface‐Shielded Vectors for Gene Delivery

Journal of Polymer Science, Volume 63, Issue 6, Page 1419-1432, 15 March 2025.
This study develops synthetic polycationic di‐block carriers for nucleic acid (NA) delivery in gene therapy. Consisting of a cationic block and a hydrophilic block, these carriers efficiently form complexes with NAs and shield them with a protective bioinert layer, enhancing stability during circulation in the bloodstream while reducing undesirable ...
Eliška Hrdá, Ladislav Androvič, Marcela Filipová, Michal Pechar, Richard Laga   +4 more
wiley   +1 more source

Syndrome of Inappropriate Antidiuretic Hormone Secretion and Thrombotic Microangiopathy as Paraneoplastic Syndromes Complicating BRCA2-Mutated Metastatic Prostate Cancer. [PDF]

Cureus
Shapoo N, Izaguirre C, Rehman A, Mattana J, Gotlieb V.   +4 more
europepmc   +1 more source

Polyethylene‐Polyamide‐6 Diblock Copolymers for Fused Filament Fabrication

Journal of Polymer Science, EarlyView.
Linear HDPE‐PA6 block copolymers were prepared by polymerization of ethylene to a macroinitiator and subsequent anionic caprolactam polymerization. The copolymer with a HDPE mass of 6500 Da and PA6 mass of 20.000 Da was used as a filament in 3D printing.
Elsa M. Schoeneberger, Gerrit A. Luinstra   +1 more
wiley   +1 more source

Nonlocal Electrical Detection of Spin‐Polarized Surface Currents in the 3D Topological Insulator BiSbTeSe2

physica status solidi (b), EarlyView.
Nonlocal (NL) electrical measurements in the topological insulator BiSbTeSe2 reveal spin‐polarized surface currents, which vanish around 20 K due to increased interactions between bulk and surface states. An enhanced spin‐to‐background ratio in the NL geometry compared to the local geometry provides new insights into spin transport and current pathways
Shaham Jafarpisheh, Frank Volmer, Zhiwei Wang, Bárbara Canto, Yoichi Ando, Christoph Stampfer, Bernd Beschoten   +6 more
wiley   +1 more source

Clinical differential analysis of severe complications thrombotic microangiopathy and acute graft-versus-host disease following allogeneic hematopoietic stem cell transplantation. [PDF]

Front Oncol
Wang YY, Li GP, Fu SZ, Fu YW, Shen Y, Xu QX.   +5 more
europepmc   +1 more source

Ovarian cancer subtype classification based on deep learning models on WSI and TMA images [PDF]

Yuyang Gu
openalex   +1 more source

Advances in Gate Dielectrics for 2D Electronics

physica status solidi (RRL) – Rapid Research Letters, EarlyView.
This review discusses advanced gate dielectric integration for 2D electronic devices, including layered and nonlayered dielectric materials, while highlighting strategies such as seed‐assisted ALD, transfer methods, and in situ oxidation. By focusing on interface engineering and materials innovation, new routes for scalable, high‐performance 2D ...
Moon‐Chul Jung, Jiwoo Kim, Gwan‐Hyoung Lee   +2 more
wiley   +1 more source