Results 11 to 20 of about 10,867,351 (301)

Reliability and fault tolerance modelling of multiprocessor systems [PDF]

, 1989
This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University.Reliability evaluation by analytic modelling constitute an important issue of designing a reliable multiprocessor system.
Valdivia, Roberto Abraham
core   +6 more sources

Exploring the design applications of key emerging materials from natural sciences through a design ideation workshop [PDF]

, 2023
10th Congress of the International Association of Societies of Design Research (IASDR 2023) 9-13 October 2023, Milan, Italy202405 bcchVersion of ...
Wang, X, Tufail, M, Leung, Sai Yin, Park, Hyunyim, Tian, A, Uzma, S, Kim, KM, Kim, KwanMyung, Wang, Xinyi, Tufail, Muhammad, Li, X, Tian, Aichu, Leung, SY, Park, H, Li, Xinye, Uzma, Sahr   +15 more
core   +1 more source

Software modification aided transient error tolerance for embedded systems

, 2013
Commercial off-the-shelf (COTS) components are increasingly being employed in embedded systems due to their high performance at low cost. With emerging reliability requirements, design of these components using traditional hardware redundancy incur large
Kim Sunesen, Sunesen, Kim, Mathew, J., Pradhan, Dhiraj K., Gerard Rauwerda, Sunesen, K., Ioannis Sourdis, Shafik, Rishad Ahmed, Potman, J., Potman, Jordy, Sourdis, Ioannis, Rishad A. Shafik, Shafik, R.A., Rauwerda, G.K., Jimson Mathew, Pradhan, D.K., Dhiraj K. Pradhan, Mathew, Jimson, Rauwerda, Gerard, Jordy Potman, Mathew, J.,, Rauwerda, G.K.,, Sunesen, K.,, Pradhan, D.K.,, Potman, J.,, Sourdis, Ioannis,, Shafik, R.A.,   +26 more
core   +2 more sources

A study on tolerances design of parallel link robots based on mathematical models

Journal of Advanced Mechanical Design, Systems, and Manufacturing, 2018
Parallel link robots are now being applied to various assembling tasks for small products and components. One of the important issues for design of the parallel link robots is to improve their kinematic motion deviations due to the complex link ...
Ryo TAKEMATSU, Naoki SATONAKA, Wiroj THASANA, Koji IWAMURA, Nobuhiro SUGIMURA   +4 more
doaj   +1 more source

3D SOI edge coupler design for high tolerance

AIP Advances, 2023
We designed and manufactured two single-mode fiber-to-chip three-dimensional (3D) edge couplers with taper and semi-cone structures on a 3.5 µm silicon device layer of a silicon-on-insulator.
Shengtao Yu, Xiaoyu Li, Chengqun Gui
doaj   +1 more source

Fault tolerant design for autonomous vehicle [PDF]

2017 4th International Conference on Control, Decision and Information Technologies (CoDIT), 2017
A fault-tolerant control design strategy based upon sliding mode control and a descriptor observer for Upschitz system is presented. The aim is to mitigate the vehicle speed faults and provide accurate measurements for the control. Thus, the additive faults affecting the vehicle speed sensor are estimated, and accurate speed measurments are used to ...
Boukhari, Mohamed Riad, Glaser, Sébastien, Chaibet, Ahmed, Boukhnifer, Moussa   +3 more
openaire   +4 more sources

Tacit Learning in an Extended Interior Design Studio [PDF]

, 2019
5th DRS Learn X Design International Conference for Design Education Researchers: Insider Knowledge, 9-12 July 2019, METU, Ankara202403 bckwVersion of RecordSelf ...
Venkatesh, A, Ma, H, Henry Ma, Venkatesh, Aruna, Aruna Venkatesh, Ma, Henry   +5 more
core   +1 more source

Fault-tolerance Design and Validation of Power Converter [PDF]

Jisuanji gongcheng, 2017
In order to improve the reliability of the Switch Reluctance Generation(SRG)system,several common failures of power converter are analyzed.Combined with the superiority of the independence of asymmetrical bridge power converter,a kind of fault-tolerant ...
ZHOU Zheng,LIU Yongzhi,SONG Jinlong,MA Weimin,WANG Zhenliang
doaj   +1 more source

A study on tolerance design of machine tool components based on shape generation motions (Theoretical analysis considering rotational table positions)

Nihon Kikai Gakkai ronbunshu, 2017
The kinematic motion deviations of the five-axis machining centers are deeply influenced by the geometric deviations of the components, such as guide-ways and bearings.
Naoki SATONAKA, Ryo TAKEMATSU, Nobuhiro SUGIMURA, Koji IWAMURA, Yoshitaka TANIMIZU   +4 more
doaj   +1 more source

Tolerance analysis method considering multifactor coupling based on the Jacobian–torsor model

Advances in Mechanical Engineering, 2022
Assembly quality affects the performance of mechanical products and reasonable tolerance designs are central to assembly quality. Unreasonable tolerance design leads to the mechanical equipment performance degradation under complex operating conditions ...
Zhaohui Yang, Wenrong Yang, Tianshi Gao, Yu Zhang   +3 more
doaj   +1 more source