Results 91 to 100 of about 5,830,632 (387)
Defining a method of evaluating die life performance by using finite element models (FEM) and a practical open die hot forging method [PDF]
, 2016 Die wear, which is defined as a surface damage or removal of material from one or both of two solid surfaces in a sliding, rolling or impact motion relative to one another, is considered the main cause of tool failure. Wear is responsible for 70% of tool
Foster, James +2 more
core +1 more source
Wear Mechanism of Cemented Carbide Tool in High Speed Milling of Stainless Steel
Chinese Journal of Mechanical Engineering, 2018 Adhesion of cutting tool and chip often occurs when machining stainless steels with cemented carbide tools. Wear mechanism of cemented carbide tool in high speed milling of stainless steel 0Cr13Ni4Mo was studied in this work.
Guang-Jun Liu +5 more
doaj +1 more source
Advanced Engineering Materials, EarlyView.Laser surface texturing significantly improves the corrosion resistance and mechanical strength of 3D‐printed iron polylactic acid (Ir‐PLA) for marine applications. Optimal laser parameters reduce corrosion by 80% and enhance tensile strength by 25% and ductility by 15%.
Mohammad Rezayat +6 more
wiley +1 more source
The influence of surface treatment of PVD coating on its quality and wear resistant [PDF]
, 2019 The article deals with a determination of the influence of a cutting edge preparation on the quality and wear resistance of coated cutting tools. Cutting inserts made from a sintered carbide with a deposited layer of PVD coating were selected for ...
Malotová, Šárka +3 more
core +1 more source
LubricantsTool wear in machining is inevitable, and determining the precise moment to change the tool is challenging, as the tool transitions from the steady wear phase to the rapid wear phase, where wear accelerates significantly.
Luís Henrique Andrade Maia +5 more
doaj +1 more source
Direct Consolidation of Copper–Graphene Composite by Rotary Swaging
Advanced Engineering Materials, EarlyView.The applicability of the rotary swaging method for preparation of electroconductive copper–graphene composite by direct consolidation of powders is proven. The consolidated material features advantageous microstructure featuring fine grains and twins, with homogeneous distribution of graphene, primarily along the twin boundaries, which contribute to ...
Radim Kocich +2 more
wiley +1 more source
Expert system for tool wear monitoring in blanking [PDF]
, 1992 A description is given of a simple yet powerful expert system created using the CRYSTAL shell which is able to monitor the potential and functional failures of the tool and the monitoring equipment.
Au, YHJ, Mardapittas, AS
core
Advanced Engineering Materials, Volume 27, Issue 13, July 2025.We develop a one‐step spray coating approach to coat the fluorinated graphene (FG) nanosheet onto the N95 respirators. The spray‐coated superhydrophobic N95 respirators can effectively repel respiratory droplets off instantaneously and prevent SARS‐CoV‐2 virus accumulation on the surface.
Fengjie He +4 more
wiley +1 more source
Reliability assessment of cutting tool life based on surrogate approximation methods [PDF]
, 2014 A novel reliability estimation approach to the cutting tools based on advanced approximation methods is proposed. Methods such as the stochastic response surface and surrogate modeling are tested, starting from a few sample points obtained through ...
Kolios, Athanasios +1 more
core +1 more source
Performance evaluation of PCBN, coated carbide and mixed ceramic inserts in finish-turning of AISI D2 steel [PDF]
Jurnal Tribologi, 2017 The present study compares the performance of three different cutting tools, viz., PCBN, mixed ceramic and coated carbide tool in finish turning of hardened D2 tool steel in terms of tool wear, surface roughness, and economic feasibility under dry ...
M. Junaid Mir, M.F. Wani
doaj