Results 11 to 20 of about 880,527 (229)

Measuring Hysteresis Loop and Optimization of the Stator Tooth Width in the Permanent Magnet Synchronous Machine [PDF]

open access: yesTransactions of the VŠB-Technical University of Ostrava, Mechanical Series, 2013
The first part of this paper deals with the measuring of hysteresis loop of the toroidal shape core. LabVIEW software is used to automate this process.
Zdeněk NOVÁK   +2 more
doaj   +2 more sources

ANALYSIS OF SELECTED SOLUTIONS AND METHODS TO LIMIT THE UNEVEN LOAD DISTRIBUTION ON THE TOOTH WIDTH [PDF]

open access: yesScientific Journal of Silesian University of Technology. Series Transport, 2017
This article is dedicated to the subject of gearboxes, with a specific focus on the load distribution on the tooth. The aim of the study was to review the selected solutions and methods that can contribute to aligning the load on the width of the tooth ...
Michał JUZEK, Grzegorz WOJNAR
doaj   +3 more sources

A method for designing a large tooth width face gear transmission

open access: yesJixie chuandong
ObjectiveDue to the phenomenon of undercutting at inner diameter and tipping at outer diameter in conventional face gears, the tooth width of face gears is limited, further affecting the improvement of their load-bearing capacity.
ZHOU Zhenyu   +3 more
doaj   +1 more source

The Effect of Student Experience and Tooth Location on Finish Line Width and Angle of Full Metal Crown Preparations in Preclinical Setting [PDF]

open access: yesAdvances in Medical Education and Practice
Nabeel Munshi Oral and Maxillofacial Prosthodontics Department, King Abdulaziz University, Faculty of Dentistry, Jeddah, Saudi ArabiaCorrespondence: Nabeel Munshi, Oral and Maxillofacial Prosthodontics Department, King Abdulaziz University Faculty of ...
Munshi N
doaj   +1 more source

Measurement of tooth size and shape in subjects with hypodontia and a control group using a new image analysis technique. [PDF]

open access: yes, 2000
The literature referred to here provided information concerning the epidemiology of hypodontia and its association with other developmental anomalies.
Al-Sharood, Mohammad H
core   +5 more sources

Diagnostic indicators of tooth flank wear based on the analysis of tooth spectral component parameters

open access: yesВестник Самарского университета: Аэрокосмическая техника, технологии и машиностроение, 2022
The wear of gear tooth flanks of aircraft gas turbine engines is the most common and the most dangerous of their defects. Practice shows that vibroacoustic diagnostics is the most effective method for monitoring the technical condition of rotary machines,
A. E. Sunduckov
doaj   +1 more source

Evaluation of Alveolar Bones in the Context of Orthodontic Single-Tooth Space Closure: A Retrospective Cone Beam Computed Tomography-Based Analysis

open access: yesApplied Sciences, 2023
In the literature, there are no studies evaluating alveolar bone width in areas with a single missing tooth in terms of orthodontic tooth movement. This study was meant to determine whether residual alveolar bone width in edentulous crests is a risk ...
Saadet Çınarsoy Ciğerim   +3 more
doaj   +1 more source

Indirect composite preparation width and depth and tooth fracture resistance.

open access: yes, 1995
PURPOSE: To evaluate the influence of preparation width and depth on the fracture resistance of teeth restored with one type of indirect composite restoration.
Wilson, N. H.   +2 more
core   +9 more sources

Comparison of Tooth Size Discrepancy of Three Main Ethnics in Malaysia with Bolton's Ratio [PDF]

open access: yes, 2014
The objective of this study was to investigate the applicability of Bolton's ratios in orthodontic population of Malaysian main ethnics; Malay, Chinese and Indians.
Othman, S. A., Abd Rahman, A. N. A.
core   +1 more source

An experimental method to measure gear tooth stiffness throughout and beyond the path of contact [PDF]

open access: yes, 2001
A method is presented that allows the accurate measurement of the tooth pair stiffness of a pair of spur gears. The method reveals the stiffness behaviour throughout the full length of the normal path of contact and also into the extended contact region ...
Munro, R. G.   +2 more
core   +1 more source

Home - About - Disclaimer - Privacy