Results 61 to 70 of about 363,979 (139)

Analysis of suitable converter for the implementation of drive system in solar photovoltaic panels

Electrical engineering & Electromechanics
Introduction. Photovoltaic (PV) systems gained immense attraction in the recent years since it produces electricity without causing environmental pollution through direct conversion of solar irradiance into electricity.
G. Themozhi, K. Srinivasan, T. Arun Srinivas, A. Prabha   +3 more
doaj   +1 more source

Predicting the Onset of Cavitation in Automotive Torque Converters—Part I: Designs with Geometric Similitude

International Journal of Rotating Machinery, 2008
Dimensional analysis has been applied to automotive torque converters to understand the response of performance to changes in torque, size, working fluid, or operating temperature. The objective of this investigation was to develop a suitable dimensional
D. L. Robinette, J. M. Schweitzer, D. G. Maddock, C. L. Anderson, J. R. Blough, M. A. Johnson   +5 more
doaj   +1 more source

Robust fuzzy controller design with FPGA implementation for matrix converter based induction motor drive

e-Prime: Advances in Electrical Engineering, Electronics and Energy
This paper aims to design a controller for a matrix converter fed induction motor drive providing less torque ripples and eliminating peak overshoots with good transient and steady state responses utilizing fuzzy and direct torque control.
Reena Meghwal, Vinod Kumar Yadav, Monika Vardia   +2 more
doaj   +1 more source

Torque converter vehicle drive

, 2020
Tato bakalářská práce se zabývá historií a funkcí hydrodynamického měniče a jeho vlivem na trakční charakteristiku vozidla. Popsány jsou jednotlivé prvky hydrodynamického měniče, rozdíly oproti hydrodynamické spojce a možnost násobení vstupního točivého ...
Tomáš Pánek
core  

Control of Brushless Doubly-Fed Reluctance Machines under Normal and Faulty Operating Conditions [PDF]

The brushless doubly fed reluctance machine (BDFRM) is an attractive alternative technology to traditional slip-ring doubly fed induction machine (DFIM) for slip-power recovery applications with limited variable speed ranges such as wind turbines or pump-
Hasan, Mohammed
core  

Are joint torque models limited by an assumption of monoarticularity? [PDF]

, 2012
This study determines whether maximal voluntary ankle plantar flexor torque could be more accurately represented using a torque generator that is a function of both knee and ankle kinematics.
Yeadon, MR, King, MA, Conceição, F, Lewis, MGC   +3 more
core  

Design and Evaluation of a Structural Analysis-Based Fault Detection and Identification Scheme for a Hydraulic Torque Converter. [PDF]

Sensors (Basel), 2018
Chen Q, Wang J, Ahmed Q.
europepmc   +1 more source

Research of the Start-off Slip Friction Control of Hydraulic Torque Converter Lockup Clutch

Jixie chuandong, 2016
Taking the Lockup clutch in the hydraulic torque converter as the study object,the strategy of start- off slip friction control for the hydraulic torque converter lockup clutch is studied.
Xue Dianlun, Chang Neng, Guo Xuekai
doaj  

Research of frequency division starting method based on six-pulse-wave AC/AC frequency converter

Gong-kuang zidonghua, 2013
Based on analysis of six-pulse-wave AC/AC frequency converter and according to principle of dual-slope voltage soft starting method, a frequency division starting method based on six-pulse-wave AC/AC frequency converter was put forward.
LI Gao-ju, DU Qing-nan, GUO Hong-liang, LIANG Jing   +3 more
doaj  

Feasibility study for convertible engine torque converter [PDF]

, 1985
The feasibility study has shown that a dump/fill type torque converter has excellent potential for the convertible fan/shaft engine. The torque converter space requirement permits internal housing within the normal flow path of a turbofan engine at ...

core