Results 121 to 130 of about 21,015 (221)

Enhancement of the Through‐Thickness Electrical Conductivity of Carbon‐Fiber‐Reinforced Plastics Using Large Graphite Particles

Advanced Engineering Materials, EarlyView.
To enhance through‐thickness conductivity without sacrificing impregnation, large spherical graphite particles are intentionally employed in a low‐viscosity resin. Unlike finer conductive fillers, these particles remain outside the fiber bundles and accumulate in resin‐rich interlaminar regions during molding.
Keito Hosoe, Yu Zhou, Shintaro Kamiyama, Takao Okada, Tomohiro Yokozeki, Ryoma Tokonami, Tatsuhiro Takahashi   +6 more
wiley   +1 more source

Control System Design and Implementation of Battery-Assisted Quasi-Impedance-Source Inverter for Standalone Power Generation. [PDF]

Sensors (Basel)
Vadi S, Özarslan Yatak M.
europepmc   +1 more source

3D‐Printed Titanium Gyroid Scaffold Structure Integrated With Tough Hybrid Materials for Cartilage Replacement

Advanced Engineering Materials, EarlyView.
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin, Gloria R. Young, Francesca Tallia, Reece N. Oosterbeek, Shaaz Ghouse, Edward Spiers, Nupur Kohli, Tom Briggs, Marc Masen, Siwei Li, Ren‐Jei Chung, Jonathan R. T. Jeffers, Julian R. Jones   +12 more
wiley   +1 more source

Near-Room-Temperature Magnetoelectric Coupling Engineered through Inversion-Breaking Tilts in a Bulk Perovskite Polytype. [PDF]

J Am Chem Soc
Simpson S, Dey U, Lees MR, Da Silva I, Bristowe NC, Senn MS.   +5 more
europepmc   +1 more source

The Role of Ultra‐Thin Passive Films and Organic Adsorbates on Aluminum Chips for a Friction‐Induced Solid‐State Recycling Process

Advanced Engineering Materials, EarlyView.
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller, Steffen Gabsa, Werner Homberg, Guido Grundmeier   +3 more
wiley   +1 more source

Machine learning-based optimization of resonant LLC converters for improved power quality in electric vehicle chargers. [PDF]

Sci Rep
Rexy AI.
europepmc   +1 more source

Elastic–Plastic Modeling and Experimental Characterization of Granular Jamming Actuators

Advanced Engineering Materials, EarlyView.
Granular jamming enables rapid switching between soft and rigid mechanical states. Here, a reduced‐order elastic‐perfectly‐plastic beam framework captures pressure‐dependent loading, unloading, residual deformation, and hysteresis in jammed beams, while matching three‐point bending experiments across materials and geometries. The framework links design
Saheli Patel, Prashant K. Purohit, Jordan R. Raney   +2 more
wiley   +1 more source

Rotary 3D Printing With Integrated Electroplating

Advanced Engineering Materials, EarlyView.
A rotary material extrusion platform integrates localized copper electroplating with printing and encapsulation to fabricate cylindrical polymer–metal structures containing fully embedded, low‐resistance conductive pathways that enable internal Joule heating and thermally activated shape‐memory responses.
Antonio Zagaria, Nicola Larovere, Moslem Mohammadi, Gianluca Percoco, Ali Zolfagharian, Gianni Stano   +5 more
wiley   +1 more source

Impact of the Process Atmosphere During Hot Isostatic Pressing on the Near‐Surface Composition of an Additively Manufactured Austenitic High‐Interstitial Steel

Advanced Engineering Materials, EarlyView.
A high interstital austenitic steel is additively manufactured and postdensified by HIP to eliminate gas porosity. Thereby, the loss of N and Mn in Ar HIP atmosphere is investigated. Further, HIP using N2 atmosphere is investigated which led to excessive nitride formation.
F. Großwendt, J. Hahn, J. Kimm, S. Weber, J. Lentz   +4 more
wiley   +1 more source

Mitigating Creep Anisotropy and Enhancing Performance in Additively Manufactured Ni‐Based Superalloys: A Review

Advanced Engineering Materials, EarlyView.
Additive manufacturing introduces pronounced microstructural and crystallographic anisotropy in Ni‐based superalloys, resulting in orientation‐dependent creep deformation and damage. This review identifies the key microstructural origins of creep anisotropy, examines their influence on dominant deformation mechanisms, and highlights processing ...
Chandan Kumar, Shobhit Pratap Singh, Gaurav Mohanty, Praveen Kumar   +3 more
wiley   +1 more source