Results 241 to 250 of about 10,155,032 (294)
Some of the next articles are maybe not open access.
A Hybrid Approach to Traction Control
2001In this paper we describe a hybrid model and an optimization-based control strategy for solving a traction control problem currently under investigation at Ford Research Laboratories. We show through simulations on a model and a realistic set of parameters that good and robust performance is achieved.
Francesco Borrelli +3 more
openaire +3 more sources
A traction control system for motocross and supermotard
2008 International Workshop on Intelligent Solutions in Embedded Systems, 2008The traction control is a widely used control system to increase stability and safety of four wheel vehicles. Automatic stability control is used in the BMW K1200R motorcycle and in motoGP competition, but not in other motorcycles. This paper presents an algorithm and a low cost real time hardware implementation for motocross and supermotard ...
Pascal Cardinale +2 more
openaire +2 more sources
Traction Control Applications in Engine Control
SAE Technical Paper Series, 2000<div class="htmlview paragraph">Traction control is an electronic means of reducing the wheel spin caused by the application of excessive power for the valuable grip. Wheel spin can result in loss control of the car, reduce acceleration and cause tire wear. In the front wheel tire the loss grip is experienced as underwater, where the front of the
Badih Jawad +4 more
openaire +1 more source
Supervisory traction control for a slipping UGV
2013 American Control Conference, 2013Unmanned Ground Vehicles (UGVs) face many mobility challenges as they operate in unstructured environments. In addition to insurmountable obstacles, UGVs can lose traction and slip, reducing maneuverability and potentially causing collisions with obstacles.
John A. Broderick +2 more
openaire +2 more sources
Fuzzy Longitudinal Traction Control
Proceedings, 2005 IEEE/ASME International Conference on Advanced Intelligent Mechatronics., 2005The traction control increases stability, safety, efficiency and range of EVs preventing slippage in acceleration and permitting to use high-efficiency low drag tires. The performance of the presented approach is comparable with that obtained by the well-recognized techniques while this approach is simpler. This paper considers the longitudinal control
DELLI COLLI V. +2 more
openaire +2 more sources
THE INFLUENCE OF THYRISTOR CONTROL ON TRACTION MOTORS
IFAC Proceedings Volumes, 1977Publisher Summary Traction duty efforts free choice of speed and acceleration of a vehicle within certain limits. Allowing for gear and wheel-diameter, the tractive effort of the vehicle responds to the motor-torque and vehicle speed to motor speed.
openaire +1 more source
Adhesion control in railroad traction
e & i Elektrotechnik und Informationstechnik, 2004This article presents a new approach to adhesion control for railroad traction. Based on a combined torque and speed observation the controller detects the actual adhesion utilization at the wheel and applies an adequate torque limitation. Hence the traction unit optimally takes use of the available adhesion.
C. Gessl, M. Glasl, A. Weinmann
openaire +1 more source
Traction Control for Commercial Vehicles
SAE Technical Paper Series, 1989<div class="htmlview paragraph">The antilock system (ABS) for commercial vehicles and buses has become increasingly popular since its market introduction in 1981. Several vehicle manufacturers already equip their vehicles with ABS as standard, instead of only if specifically requested, and have been doing so for some years now.
Reiner Emig, Herbert Schramm
openaire +1 more source
2014
Critical driving situations can occur not only while braking, but also whenever strong longitudinal forces should be transferred at the contact area between the tire and the ground. This is because the transferable lateral forces are reduced by this process.
Frank Niewels, Jürgen Schuh
openaire +2 more sources
Critical driving situations can occur not only while braking, but also whenever strong longitudinal forces should be transferred at the contact area between the tire and the ground. This is because the transferable lateral forces are reduced by this process.
Frank Niewels, Jürgen Schuh
openaire +2 more sources

