Results 231 to 240 of about 5,624,064 (301)
This study proposes a potential device design for joint cartilage replacement. Silica‐polytetrahydrofuran (SiO2‐PolyTHF) hybrids with customizable mechanical properties were developed to mimic the characteristics of a natural meniscus. These were synthesized through a two‐pot sol–gel hybrid process.
Yu‐Chien Lin +12 more
wiley +1 more source
Despite benefits to storage stability and handleability of aluminum scrap, octadecyl phosphonic acid (ODPA) SAMs reduce the tensile strength of wires produced using friction‐induced recycling. Etching and methyl diphosphonic acid (MDPA) coatings, however, have little effect.
Timothy D. Goller +3 more
wiley +1 more source
PUF/ENB microcapsules were synthesized based on a sequential factorial design and incorporated into an epoxy matrix. Their anticorrosive action, associated with the self‐healing mechanism, demonstrated that the addition of microcapsules to the coating improved anticorrosive performance compared to pure epoxy coatings, particularly when the encapsulate ...
Vandicleya Alves Moreira +6 more
wiley +1 more source
Impact of Hydrogen Incorporation on Electronic and Magnetic Structure of X2CrNi18‐9 Stainless Steel
Hydrogen uptake in austenitic stainless steel alters both its electronic and magnetic structure. Seebeck measurements reveal hydrogen‐induced shifts in the electronic density of states, while neutron scattering uncovers nanoscale inhomogeneities that grow upon hydrogen incorporation, with the most pronounced effect observed in the PBF as‐built state ...
Torben Tappe +9 more
wiley +1 more source
Microstructural evolution of premium rail steel during flash butt welding (FBW), comparing physically simulated heat‐affected zones with actual weld regions. Thermal cycles induce phase transformations and microstructural heterogeneity that influence weld quality and mechanical performance. These findings provide insights into optimizing FBW parameters
Emmanoelle Cintra da Cunha Araújo +15 more
wiley +1 more source
Particle morphology controls the balance between printability and electrical connectivity in low‐temperature AgCu/Ag metallization pastes. Flake‐shaped AgCu particles form extended low‐resistance contacts, whereas spherical particles favor processability at high metal loading. Fine Ag particles further tune void filling and conductive‐network formation
O. Mhirsi +3 more
wiley +1 more source
Gyroid Structured Globugraphite Carbon Foam With Hierarchical and Tailored Pore Size
Secondary sacrificial templates were designed and printed to create a defined network within a porous carbon. Lattices thermally degrades during the sintering process. Lattices are imprinted into the ceramic template and transferred to the morphology of Globugraphite.
Christiane Roller +6 more
wiley +1 more source
This study explores the influences of calendering and surface treatment during direct ink writing (DIW) of thermochromic cholesteric liquid crystal (CLC) on PET nonwovens. For the PVA‐coated nonwovens, calendering reduces pore size leading to reduced ink absorption and enhanced spreading. The NeverWet‐coated nonwovens improve thermochromic responses by
Sreenivasan Sreenivasan Narayanan +3 more
wiley +1 more source
A cold wall reactor is developed to coat a SiC fiber tow with BN by low pressure chemical vapor deposition. The precursor gas is triethylamine borane mixed with ammonia. The heating process induces a temperature gradient, with the temperature decreasing from the core to the surface of the multifilament tow.
Pierre Fenetaud, Sylvain Jacques
wiley +1 more source
An all‐in‐one analog AI accelerator is presented, enabling on‐chip training, weight retention, and long‐term inference acceleration. It leverages a BEOL‐integrated CMO/HfOx ReRAM array with low‐voltage operation (<1.5 V), multi‐bit capability over 32 states, low programming noise (10 nS), and near‐ideal weight transfer.
Donato Francesco Falcone +11 more
wiley +1 more source

