Results 131 to 140 of about 2,413,906 (309)

Martensitic transformation of reversed austenite in a low-carbon 7Ni steel

Philosophical Magazine Letters
Reverse transformation plays an important role in phase controlling of 7Ni steel. However, little attention has been paid on the martensitic transformation behaviour of this material.
Wei Hou, Qingdong Liu, Jianfeng Gu
doaj   +1 more source

Electrochemical Behavior of Flame‐Sprayed Sc‐Doped AlCoCrFeMo High‐Entropy Alloy Coatings in 3.5% Sodium Chloride Solution

Advanced Engineering Materials, EarlyView.
Scandium (Sc)‐doped AlCoCrFeMo HEA coatings are fabricated via flame spraying with 0.1, 0.3, and 0.5 wt% Sc additions. Among these, the HEA‐Sc0.3 coating exhibits the highest corrosion resistance, indicated by a more positive corrosion potential and lower current density.
Pankaj Kumar, Akash Vyas, Mohammad Aatif Qazi, Nashit Jalal, Maria Ophelia Jarligo, Mostafa Yakout, Jing Liu, André McDonald   +7 more
wiley   +1 more source

Transformation Kinetics of Burnt Lime in Freshwater and Sea Water. [PDF]

Materials (Basel), 2020
Justnes H, Escudero-Oñate C, Garmo ØA, Mengede M.   +3 more
europepmc   +1 more source

Martensite transformation of sub-micron retained austenite in ultra-fine grained manganese transformation-induced plasticity steel

, 2018
The influence of the chemical composition and the grain size of retained austenite in an ultra-fine grained medium manganese steel on the martensite transformation kinetics was investigated by means of dilatometry.
Seawoong Lee, Seok-Jae Lee, De Cooman, BC   +2 more
core   +1 more source

Influence of Scan Strategies in Electron Beam Powder Bed Fusion on Solidification, Microstructure, and High‐Temperature Compressive Properties of γ′‐Strengthened Inconel 738LC

Advanced Engineering Materials, EarlyView.
Experiments and thermophysical simulations were conducted to investigate the electron beam powder bed fusion electron beam (PBF‐EB/M) process for the γ′‐strengthened nickel‐based superalloy Inconel 738LC. The results demonstrate the impact of process‐induced microstructural variations on high‐temperature mechanical behavior, providing a basis for ...
Jan Niklas Petenati, Karthik Kumar Banku, Prasanth Bondi, Ivan Zhirnov, Yangyiwei Yang, Gordon Schmidt, Jürgen Christen, Georg Hasemann, Manja Krüger, Bai‐Xiang Xu, Bilal Gökce, Silja‐Katharina Rittinghaus   +11 more
wiley   +1 more source

Modelling of phase transformation kinetics in steels and coupling with heat treatment residual stress predictions

, 1999
One keypoint for the prediction of heat treatment residual stresses is the modelling of phase transformation kinetics and of their consequences on the thermomechanical behaviour of the material.
J.Ch. Louin, C. Aubry, A. Simon, S. Denis, A. Mey, P. Archambault   +5 more
core   +1 more source

High‐Temperature Phase Transformation in a V‐9Si‐6.5B Alloy: The Kinetic and Crystallographic Pathway From V5SiB2 to V8SiB4

Advanced Engineering Materials, EarlyView.
In situ synchrotron high‐energy X‐ray diffraction reveals the real‐time high‐temperature phase evolution of a ternary V‐9Si‐6.5B alloy. The study uncovers a kinetically delayed V5SiB2 → V8SiB4 transformation governed by massive structural and chemical barriers.
Zahra Sabeti, Andreas Stark, Roja Rani Korrayi, Florian Pyczak, Georg Hasemann   +4 more
wiley   +1 more source

Effect of Hot Deformation on Phase Transformation Kinetics in Isothermally Annealed 3Mn-1.6Al Steel. [PDF]

Materials (Basel), 2020
Skowronek A, Morawiec M, Kozłowska A, Pakieła W.   +3 more
europepmc   +1 more source

Kinetics of Hydrothermally Induced Transformation of Yttria Partially Stabilized Zirconia

, 2007
Yttria-stabilized zirconia undergoes tetragonal to monoclinic phase transformation under hydrothermal conditions in the temperature range of 150–350 °C. Phase transformation accompanied by volume change in bulk yttria partially stabilized zirconia (YPSZ)
Payyapilly, J. J., Butt, D. P.
core   +1 more source

Impact of MgO Additions on the Oxidation Resistance and Compression Behavior of Vanadium Alloys

Advanced Engineering Materials, EarlyView.
An increase in oxidation resistance at 600 °C is achieved for alloys containing more than 2.5 wt.% MgO. It has been established that, along with V2O5, MgO6V2, and Mg2O7V2 are formed, which are presumed to enhance oxidative stability. Furthermore, the possible transformation of Mg‐vanadates through reaction with CO2, which presumably occurs in this ...
Ievgen Solodkyi, Mathias Galetz, Georg Hasemann, Fabian Lanoy, Emma White, Manja Krüger   +5 more
wiley   +1 more source