Results 211 to 220 of about 451,642 (327)

Influence of Sample Preparation and Processing Procedures on the Thermal Diffusivity of MgO‐C Refractories

Advanced Engineering Materials, EarlyView.
The thermal diffusivity of MgO‐C refractories is highly sensitive to sample preparation and processing procedures. In this article, the effects of coking sequence, machining conditions, structural inhomogeneity, and graphite coating application on measurements using laser flash apparatus are systematically investigated.
Luyao Pan, Rhena Wulf, Till M. J. Stadtmüller, Christos G. Aneziris, Tobias M. Fieback   +4 more
wiley   +1 more source

Reinforcement learning-driven model predictive control for optimizing counter-rotating permanent magnet synchronous motor in submarine propulsion system. [PDF]

Sci Rep
Delelew EY, Dulecha KA, Ararso ZT, Abdissa CM.   +3 more
europepmc   +1 more source

Investigation of Laser Ablation and Brush Pre‐Treatments for AlCu Cold Roll Bonding in Oxygen‐Free Conditions

Advanced Engineering Materials, EarlyView.
It is shown that laser ablation pretreatment under oxygen‐free conditions enables copper–aluminium bonding at significantly lower deformation degrees and improved properties compared to mechanical brushing. Laser ablation further increases interface contact area and induces favourable residual stress states and microstructural compatibility ...
Khemais Barienti, Finn‐Lennard Janthur, Selina Raumel, Sascha Jan Zimmermann, Sarah Seffer, René Gustus, Sebastian Herbst, Marc C. Wurz, Ludger Overmeyer, Wolfgang Maus‐Friedrichs, Hans Jürgen Maier, Florian Nürnberger   +11 more
wiley   +1 more source

The Electromechanical Connectome: Integrating Voltage, Mechanical Nano-Forces, and Subcellular Fluid Phase Dynamics in Human Neural Computation. [PDF]

Int J Mol Sci
Filipoiu FM, Tataru CI, Dobrin N, Șerban M, Covache-Busuioc RA, Toader C, Radoi MP, Munteanu O, Enyedi M.   +8 more
europepmc   +1 more source

Characterization of Nitinol Produced by Laser Powder Bed Fusion for Mechanical Metamaterial Applications

Advanced Engineering Materials, EarlyView.
Stabilization of L‐PBF Ni50.7Ti49.3 under low‐cycle loading was investigated. Recoverable strain after cycling was dependent on the amount of applied load. Recovery ratio was 53.4% and 35.1% at intermediate and high load, respectively. The maximum total strain reached 10.3% at a high load of 1200 MPa.
Ondřej Červinek, Jakub Hurník, Miroslav Šmíd, Ondřej Zobač, Melanie Todt, Daniel Koutný   +5 more
wiley   +1 more source

Enhancing stability in renewable energy transmission using multi-terminal HVDC systems with grid-forming controls for offshore and onshore wind integration. [PDF]

Sci Rep
Shufian A, Hossain MI, Anonto HZ, Rohan AI.   +3 more
europepmc   +1 more source

Handbook of Establishing and Maintaining Oxygen‐Free Atmospheres

Advanced Engineering Materials, EarlyView.
This study presents a practical framework for creating oxygen‐free atmospheres at ambient pressure using silane‐doped inert gases. The results show that ultra‐low oxygen levels and strongly reduced water content can be achieved through controlled silane dosing, drying systems, and sensor monitoring.
Sascha Jan Zimmermann, René Gustus, Lienhard Wegewitz, Wolfgang Maus‐Friedrichs   +3 more
wiley   +1 more source

Study on the fast response characteristics and mechanical reliability of high-voltage circuit breaker solenoid valves. [PDF]

Sci Rep
Zhang Y, Zhang G, Wang X, Sun Y, Gao B.
europepmc   +1 more source

Oxide‐Free Titanium Coatings by Wire Arc Spraying in a Silane‐Doped Inert Atmosphere

Advanced Engineering Materials, EarlyView.
A silane‐doped argon atmosphere enables the production of oxide‐free titanium coatings via twin‐wire arc spraying at ambient pressure. This innovative approach eliminates residual oxygen, creating process conditions that prevent oxidation and nitride formation.
Manuel Rodriguez Diaz, Maik Szafarska, René Gustus, Kai Möhwald, Hans Jürgen Maier   +4 more
wiley   +1 more source